搜索资源列表
keytest
- ok6410裸机程序！按键点亮LED！每个按键对应一个LED！-created by zhaozhixin!
led
- 点亮屏幕的一个程序文件，你可以只有的控制它的亮度和两的时间。-Lit screen a program file, you can only control its brightness and time.
a0
- 利用定时器中断，每隔一秒，循环点亮LED灯。-Use timer interrupt every second, recycling lit LED lights.
led
- LED逐渐点亮再逐渐熄灭，根据延时时间的递增递减来实现-LED light up gradually and then gradually extinguished, according to delay time to achieve incremental decrease
LED
- 点亮数码管，汇编语言实现的，8位数码管 -Highlight digital tube, assembly language to achieve, 8-bit digital tube
LED
- tms320ls2407跑马灯程序,实现小灯陆续点亮功能-Marquee tms320ls2407 procedures have lit a small lamp function
123
- 用DS18B20测量室温并在数码管上显示。 用中断方式读取四个独立式按键的键值，同时用D1~D4四个LED的点亮来指示k1~K4四个按键的按下-DS18B20 measured at room temperature and used in the digital tube display. With interruption of the way to read the four stand-alone keypad keys, D1 ~ D4 simultaneously with fo
led
- 基于EasyARM615开发板的用ucos的LED循环点亮程序。-EasyARM615 development board based on the use of LED cycle light ucos procedures.
caideng
- 设计并调试好一个16*16 LED点阵组成的彩灯图案，要求一种花案模式一直循环，最后用EL-EDA-V型EDA实验开发系统进行硬件验证。 图案：实现16*16点阵的16行同时从上往下依次点亮，全亮后16行又同时从下往上依次熄灭； -Design and debug a good 16* 16 LED lantern patterns composed of dot-matrix, to a flower cycle model has been the case, and finally
jidianqi111
- 这是一个 基本 点亮 led等的程序-This is a basic procedure, such as light led
LSD_TEXT
- 使用Keil c51软件开发，经过编程，将程序下载至单片机STC开发板上。得到的效果：D1-D3-D2-D4-D3-D5-D6-D5-D7-D6-D8-D7-D1-D8-D2-D1-D3-...的次序点亮LED灯。-failed to translate
LED
- PL2148端口实现KEY按键点亮对应的LED-nnd
VHDLLED
- VHDL点亮LED的程序. 利用分频器来实现。-VHDL LED PROGRAM
DS18B20temperaturesensor
- DS18B20 温度传感器读数据源程序 系统由中央控制单片机、温度检测器、时钟系统及显示器部分组成。控制器采用单片机AT89C51，温度检测部分采用DS18B20温度传感器，时钟系统用LED作为显示器。 单片机对数据处理后显示时间；温度传感器DS18B20采集温度信号送该给单片机处理，再把时间数据和温度数据送七段LED显示器显示，该系统还具有限温控制，当温度高于或低于某一给定温度值时分别有红灯和绿灯点亮提示，并伴随着蜂鸣器声音提示。本系统同时具有调节高低温上下限，时间调节功能-DS18B20
indep_key
- keil开发环境，独立点亮LED，流水灯，延时-base on keil ,ingnite the led independedly
EMD_DESIGN
- 用protues点亮led，用arm环境写程序-Led light with protues
leds
- S3C2440开发板自带的程序，主要功能是点亮LED灯，基于ADS1.2DE -S3C2440 development board' s own procedures, the main function is to light up LED lights, based on ADS1.2DE
xianshi
- 点亮LED 新手开发小程序 proteus试用以及测试 上手必备-New development of small LED light proteus trial procedures and testing required to use huh
LED
- P2_0口控制第一位LED灯循环点亮。用到了延时函数。-P2_0 I control cycle of the first lit LED lights. Use the delay function.
led
- 可以点亮信号灯。通过高低电平的控制，来实现灯的亮灭-Lights can be lit. Through level control to achieve the bright lights out