搜索资源列表
IO2ACPL
- 主要功能为通过单片机IO口检测交流过零信号,本程序测量50hz和60hz交流过零信号并通过LED指示-Main function of microcontroller IO port through the exchange of zero-crossing detection signal, this procedure measured 50hz and 60hz AC zero-crossing signals and instructions through the LED
AD
- 1. 构建8051单片机外部总线,扩展ADC0808 A/D转换器; 2. 用8051串行口扩展连接4位八段LED数码显示器; 3. 按1、2要求完成系统电路设计; 4. 在A/D模拟通道输入50Hz/2Vpp三角波信号,编制C51程序测量三角波的幅度平均值并显示。 -1. To build the external bus 8051, extended ADC0808 A/D converter 2. With the 8051 serial port extension t
filter50
- 模拟心电信号ECG,同时设置不同强度的50Hz干扰信号并通过50Hz陷波器消除干扰。-The signal of ECG and 50Hz filter
dpl
- PIC12C508单片机控制灯光源程序以上程序使用PIC12C508单片机,内部4MHZ时钟,4脚输入50HZ脉冲信号,7,6,3脚(GP0,GP1,GP4端口)为输出口 本文来源于虾客源码 http://www.xkxz.com-PIC12C508 MCU control over light source uses PIC12C508 microcontroller, the internal 4MHZ clock, four feet 50HZ input pulse signal,
bp
- 基于MATLAB的FIR带阻数字滤波器的设计 由于生物医学信号处理过程中易混入50Hz噪声的特点,本文利用程序设计法和FDATool设计法-Based on the MATLAB FIR digital filters with resistance of biomedical signal processing design due process characteristics of noise, with isolator using the program design method a
50HZ_signal
- 一个用SN8P2501B实现的50HZ方波信号源,可以烧一个用于过零信号的仿真。-50HZ with SN8P2501B achieve a square wave signal source, you can burn one for the zero-signal simulation.
ADcontrol
- 设计并制作数控直流电流源。输入交流200~240V,50Hz;输出直流电压≤10V-Design and production of numerical control DC current source. Input AC 200 ~ 240V, 50Hz output voltage ≤ 10V
PWM
- 随着国民经济的发展,人们需要对各中加热炉、热处理炉、反应炉和锅炉中温度进行监测和控制。采用单片机来对他们控制不仅具有控制方便,简单和灵活性大等优点,而且可以大幅度提高被控温度的技术指标,从而能够大大的提高产品的质量和数量。 本设计采用无ROM的8031作为主控制芯片。8031的接口电路有8155、2764。8155用于键盘/LED显示器接口,2764可作为8031的外部ROM存储器。其中温度控制电路是通过可控硅调功器实现的。双向可控硅管和加热丝串联接在交流220V,50HZ交流试点回路,在给
6
- 4位数码扫描显示电路,我们控制一个七段LED需要8个输出端口;如果要输出四位十进制数,就需要32的输出端口,这将占用大量的端口资源。采用串行扫描显示,我们只需要8+4共12个端口即可。其原理是:用一个四位的输出端控制,某一时刻只选中其中的一个LED(输出为‘1’表示选中),八位的输出端将该LED所需要显示的值输出;然后四位的输出端值改变,选中下一个LED。这样依次类推。如果选择的频率很快,达到50Hz以上,由于人眼的视觉暂留效应,看起来就像4个LED同时显示。 设计一个程序,输入四个一位十
last
- 微机原理与接口技术———倍频信号发生器的的分析与设计 )主要任务:有一输入方波信号f0(50Hz~100Hz),时钟信号1MHz。要求输出信号: f1=2* f0, f2=4* f0。(自动跟踪) -Microcomputer Principle and Interface Technology--- Frequency Signal Analysis and Design of generator) Main tasks: there is a square wave input
ECG_FILTER
- 心电滤波算法,可滤除基线漂移、50HZ工频干扰-ECG filtering algorithm is used to remove baseline drift, 50HZ frequency interference
CocurrentVoltageStabilizedSource
- 本设计制作一个多路输出直流稳压电源,可将220V/50Hz交流电转换为多路直流稳压电源 输出:±12V/1A,±5V/1A,一组可调正电压+3~+18V/1A -CocurrentVoltageStabilizedSource
66FFma
- 高准确度,支持50Hz/60Hz IEC 687/1036 标准的准确度要求,在500:1 的动态范围内误差小于0.1 -High accuracy, supports 50Hz/60Hz IEC 687/1036 standard accuracy requirements, the 500:1 dynamic range of error is less than 0.1
ATmega16DAC
- Avr wave.sin wave with dac 50hz.invertor
50hz_SPWM.180
- 基于STC89C51的50HZ的SPWM波,可用于光复并网发电模拟装置-Based STC89C51 the 50HZ of the SPWM wave, can be used for recovery of grid simulator
1
- msp430 逆变,单相逆变,载波20kHz,调制波50Hz,-Inverter, single-phase inverter, carrier 20kHz, modulation wave 50Hz,
081701
- msp430,单相逆变,载波20kHz,调制波50Hz-msp430, single-phase inverter, carrier 20kHz, modulation wave 50Hz
zisheyingxianboqisheji
- 使用理想低通滤波器设计针对50Hz工作频率干扰的陷波器-Ideal filters using the low road at 50hz work of the frequency interference
count
- 对脉冲进行计数,要求脉冲频率不得超过50HZ(C51源码)-Pulse count, pulse frequency required no more than 50HZ (C51 source)
PWMa
- making 3 phase balance 380v 50hz voltage source with pwm