搜索资源列表
shukongdianyuan
- 采用STC12C5A60S2单片机为核心控制器件,用输出信号采集调理电路对输出的电压、电流进行实时采样,然后把采样的值送给内部自带AD转换的STC12C5A60S2进行处理,之后控制液晶来同时显示当前输出的的电压和电流值的系统设计和实现方法。通过完整的软硬件设计,可实现竞赛课题的基本部分和提高部分的功能要求。系统硬件主要由STC12C5A60S2核心控制电路,液晶显示电路,掉电保护电路,键盘电路,稳压电源输出电路,信号采集调理电路, DA转换电路,输出电压调理电路,声光报警电路和为系统供电的电源
szdl
- Multisim 仿真 数字电路 触发器555 AD/DA-Multisim simulation of digital circuits trigger 555 AD/DA
msp430f425
- 该电路采用msp430f425低功耗单片机,AD转换,LCD驱动,USB转串口-This circuit uses low-power microcontroller msp430f425, AD converter, LCD driver, USB to Serial
Ths1207
- VHDL实现Ths1207控制器,根据硬件电路对THS1207进行配置,并读取AD转换结果。-VHDL implementation Ths1207 controller, according to the hardware circuit configuration of the THS1207, and read the AD conversion result.
keilc_TLC2543AD_proteus
- 12位精度AD转换的proteus电路及程序,实现功能是,通过4个数码管显示,采集到的数据,依次滚动显示。ADC选用TLC2543AD-12 bit AD conversion circuit proteus and procedures to achieve the function, through four digital display, the data collected, in order to scroll. ADC selection TLC2543AD
1212323351
- 本次设计用单片机芯片AT89s52设计一个数字万用表,能够测量交、直流电压值、直流电流、直流电阻以及电容,四位数码显示。此系统由分流电阻、分压电阻、基准电阻、电容测试芯片电路、51单片机最小系统、显示部分、报警部分、AD转换和控制部分组成。-The design used to design a single chip AT89s52 digital multimeter can measure AC and DC voltage, DC current, DC resistance an
AD0809
- 我们在做一个单片机系统时,常常会遇到这样那样的数据采集,在这些被采集的数据中,大部分可以通过我们的I/O口扩展接口电路直接得到,由于51单片机大部分不带AD转换器,所以模拟量的采集就必须靠A/D或V/F实现。下现我们就来了解一下AD0809与51单片机的接口及其程序设计。-We do a single-chip system, often encounter this kind of data collection, these data were collected, most by our
PAPER
- 基于FPGA的高速并行A_D采样控制电路的设计-AD high speed sampling circuit design based on FPGA
szdwqdyy
- 数字电位器在AD转换中的应用,数字电位器对于有些电路设计来讲很有用-Digital potentiometer in the AD converter in the application, the digital potentiometer in terms of circuit design for some useful
ADcaiyangDAshuchu
- AD采样正炫波,DA把波形输出,一个采样电路,包括工程在内-AD sample is Hyun Bo, DA the waveform output, a sampling circuit, including engineering, including
diangong
- 这是我学校电子工程设计的一个题目,是一个基于温度传感器的系统开发,包括了驱动电路,变送器,电源,AD,DA-This is a school of electronic engineering topics, is a temperature sensor-based system development, including a driver circuit, transmitter, power supply, AD, DA
CPLD
- CPLD + CAN总线改造,采用CPLD 进行编程,实现移相编码和电机功率输出, CAN总线进行数据通讯,使各节点独立工作又集中管理,实现集散控制。节点电机调速方案中,微控制器选用8位高性能微转换器ADμC812,逻辑与伺服控制采用全数字化方式,晶闸管主电路触发器选用ALTERA公司的 EPM7256S CPLD来完成。-CPLD+ CAN bus transformation, using CPLD for programming, coding and phase motor power
51
- 51单片机设计数字电压表,AD转换电路采用ADC08008-Single chip 89C51 design digital voltage meter
Ananlog_1
- 模拟电路学习,里面有关于放大器,ad转换等模拟电路设计方面的知识-Analog circuits learning,There are on the amplifier, ad conversion analog circuit design knowledge
hex2decadifferential-coefficient
- 在对电压做AD采样时,经常会遇到运放电路,而运放倍数的求解经常让人头疼,此程序就可轻松的求解运放倍数。程序中还包括了十六进制转十进制,绘制曲线,和对曲线求斜率的方法。-When we use the ADC to sample voltage,we often face the difficult amplifier and working out the parameter of amplifier is hard.Now the problem is solved by this progr
Intelligent-lighting
- 在keil下编译,硬件条件:51单片机,DS1302芯片,运放电路,AD转换芯片,LCD,以及红外遥控器,LED灯。可以实现通过按键或遥控调节led灯的亮度,并可设置灯的点燃时间段,根据环境光强自动调节光强的功能-In the keil compile, hardware conditions: 51 SCM, DS1302 chip, amplifier, AD transform chip, LCD, and infrared remote control, LED lamp. Can re
dianyabiao
- 用汇编语言编写的数字电压表,在protues环境下调试通过。分辨率:1mV,上下限报警功能,可调上下限,前置信号调理电路,AD转换器采用MAX1241,可与上位机通信,将实时数据上传。-Written in assembly language of the digital voltmeter, protues environment through debugging. Resolution: 1mV, upper and lower alarm function, adjustable upp
mp3SCH
- mp3 原理图,功能详尽,包括电源模块,音频模块,视频模块,ad采样模块,滤波电路仅供参考-full of mp3 sch,if you need to receive more files please tell me thank you very much
LTC2488
- 官方提供的LTC2488AD采集参考电路-LTC2488 AD
12C5616AD_nokia5110
- STC12C5616AD+Nokia5110液晶屏做的电阻触摸屏驱动电路,通过AD转换将模拟电压转换为数字值,每次按下button1时单片机将读取一次坐标值显示到5110液晶上。-STC12C5616AD+ do Nokia5110 LCD resistive touch screen driver circuit by AD converter analog voltage is converted to numeric values , each time you