搜索资源列表
e05mle132a
- NRF24LE1 GPIO UART 发送 接收 等例程-NRF24LE1 GPIO UART RX TX ....SOURCE CODE
KRX异常目标检测论文
- Kernel RX: a new nonlinear anomaly detector Heesung Kwon and Nasser M. Nasrabadi.这是KRX异常检测算法论文原文。
Arduino_ublox
- Arduino uno板子 需先下载程序后接线，否则会下载失败 GPS模块VCC Arduino的5v GPS模块GND Arduino的GND GPS模块TXD Arduino的RX（数字IO 0） GPS模块RXD不接 GPS模块PPS不接 若使用Arduino leonardo板子 需要将代码中所有的Serial修改为Serial1-Arduino uno board Need to download the program after the w
NVP6134B_Product_Brief
- NVP6134B AHD RX 芯片支持300MP摄像机-The NVP6134B AHD RX chip supports 300MP cameras
I2C_of_MSP430F249
- This demo connects two MSP430 s via the I2C bus. The master reads 5 bytes the slave. This is the MASTER CODE. The data the slave transmitter begins at 0 and increments with each transfer. The USCI_B0 RX interrupt is used to know when new data h
SPI_of_MSP430F249
- SPI master talks to SPI slave using 3-wire mode. Incrementing data is sent by the master starting at 0x01. Received data is expected to be same as the previous transmission TXData = RXData-1. USCI RX ISR is used to handle communication with
UART_of_MSP430F249
- Echo a received character, RX ISR used. Normal mode is LPM0. USCI_A0 RX interrupt triggers TX Echo. Baud rate divider with 1MHz = 1MHz/19200 = ~52.1 ACLK = n/a, MCLK = SMCLK = CALxxx_1MHZ = 1MHz
OFDM Tx Rx
- labview 实现用 usrp 进行 OFDM 传输文本，此实例提供丰富详尽的代码资源。适合新手参考学习。(LabVIEW implementation using USRP for OFDM transmission text, this example provides rich detailed code resources. For novice reference learning.)
an-r01an1721ej0220-rx-gpio
- 瑞萨RX32T开发板gpio例程，官网下载的版本(renesa RX32T gpio example)
DobotDemoForSTM32
- 本 Demo 是基于 STM32F103VET6 芯片编写，因此使用本程序时需要用户自行配备一块 STM32F103VET6 开发板。（使用其他型号的芯片需要自行移植） 通讯的端口使用了机械臂扩展 10P 接口，接口的类型是 FC-10P，接口的定义如下图 7 所示。我们需要用 RX、TX、GND 这三个端口，如图 8 机械臂与开发板连接 RX->TX1， TX->RX1，GND->GND。(The Demo is based on STM32F103VET6 chip pre
程序
- void main(void) { TMOD=0x01; //设T0为方式1，GATE=1； TH0=0; TL0=0; ET0=1; //允许T0中断 EA=1; //开启总中断 InitLcd1602(); LcdShowStr(0,0,PuZh); while(1) { StartModule(); while(!Echo); //当RX为零时等待
70Cm-RX-FL1216-MK2
- 70cm trancsjeyg edgter kklk
te7022
- TEL7022程序，TXT。TEL7022程序TEL7022程序(USB 2.0 Full-Speed compliant supported USB Audio Class 1.0 16/24 bit Resolutions supported 8/16/32/44.1/48/96 KHz sampling rates supported 2-input channels and 2-output channels supported by one I2S pairs
uart
- 基于verilog的fpga串口通信,rx,tx.两根线(Basend on verilog fpga uart tong xin)
步进电机控制
- 本篇说明文档介绍了基于RX/23T单片机的步进电机控制。主要介绍了如何在代码生成工具e2 studio下配置本例程所需要的CLOCK、PORT和MTU等模块并生成相应的驱动代码，同时对生成代码文件添加的步进电机控制、转速调整等功能进行了详细说明。最后附步进电机控制实例。(This document describes the stepper motor control based on RX/23T microcontroller. Mainly introduces how the code
OTU_RXBLK
- cctv otu rx block source
Airoha.AB1100SF_FamilyMPTool_20140703_3.1.19.0
- 该模块主要用于短距离的音乐传输，可以方便地和笔记本电脑，手机， PAD 等数码产品的蓝牙设备连接，实现音乐的无线传输。如： 蓝牙音响 蓝牙耳机 蓝牙无线传输音频 蓝牙免提电话(13 PO1 Digital GPIO, default pull-high input FWD key 14 P04 Digital GPIO, default pull-high input. MUTE I/O or NFC detection pin 15 GND Power Ground 1
new_simulation
- 通过时钟使普通的IO口模拟UART串口通讯(Use Timer_A CCR1 hardware output modes and CCR0 SCCI data latch // to implement UART function @ 2400 baud. Software does not directly read and // write to RX and TX pins, instead proper use of output modes and SCCI data // la
SI4463串口透明传输程序和上位机程序
- 51单片机实现对无线模块的数据传输。上位机程序(The primary states of the Si446x are shown in Figure 6. The shutdown state completely shuts down the radio to minimize current consumption. Standby/Sleep, SPI Active, Ready, TX Tune, andRX tune are available to optimize the
node programe RX（STM32读取DHT11的程序）
- STM32读取DHT11的程序，DHT11的供电电压为3---5.5V。传感器上电后，要等待1s以越过不稳定状态在此期间无需发送任何指令。(STM32 read DHT11 procedures, the power supply voltage of DHT11 to 3---5.5V. The sensor is powered on, wait for 1s to pass the unstable state during this period without sending any