搜索资源列表
dianji
- 直流伺服电机转速 PID控制系统仿真 利用MATLAB中的simulink 对直流伺服电机的转速进行仿真-DC servo motor speed PID control system simulation using MATLAB simulink in the speed DC servo motor simulation
DC-MOTOR-PID
- 基于51单片机的步进电机测速及控制,同时可即时显示速度值 -51 step motor based on speed and control, while the speed value can be immediately displayed
Brushless_DC_Motor_Control_System_and_Implementati
- 无刷直流电机控制系统的研究与实现 简单介绍了无刷直流电动机的工作原理,分析并确定了主回路的导通方式,控制器一是以专用芯片MC33035来进行设计,位置反馈元件有霍尔传感器反馈接口和编码器接口,开关器件采用MOSFET管,设计有转速反馈闭环控制、正反转、过电流保护等。控制器还采用89C52单片机、 MAX7219、AD667等来实现数字转速给定和转速显示。控制器二是基于PICSF4431电动机控制专用芯片,采用全数字PID控制,有转速、电流双反馈,位置反馈采用编码器反馈,开关器件采用IGBT,
FPGAmotor
- FPGA在直流电机调速中的应用,利用fpga进行PID闭环控制-tell us speed control for DC motor by FPGA,use fpga for PID circle control
dcspeedcontrol
- This simulation demonsrtates the control of a dc motor using a speed control and current control loops.Typical dynamic responses od the dc motor are also shown. The motor is initially at standstill and at no load when a step command in speed is app
IRobstacleavoidancerobotdesign
- 红外避障机器人设计--CCTV 2007机器人设计大赛 自动机器人的控制系统主要包括:CPU及外围电路、12V及24V直流电机驱动电路、直流电机保护电路、巡线传感器及其处理电路。CPU采用C8051Fxxx系列中的C8051F020单片机,外部晶振采用11.0592MHz;该自动机器人采用后轮驱动,电机采用直流电机,直流电机控制简单,使用PWM脉宽调制技术即可调节电机转速;而电机驱动电路采用双极性H桥电机驱动电路。-IR obstacle avoidance robot design- CC
source
- DC Motor Speed Modeling in Simulink by pid with Adding a lag controller
Motor-speed-to-control
- 电机调速 可以控制直流电机的速度 C编写-Motor speed to control the speed of DC motor
dc_motor_control_speed_control_pid
- This example describes how to develop speed and position control systems for a DC motor with a load. Various methods are used and the focus is on how to model and implement the various parts and not of parameter tuning. An important thing to note is
Dc-motor-of-the-PWM-speed
- 用52单片机输出PWM调速直流电机,实现电机的正反转,占空比可调,自动可以在速度设定下实现反馈调节-With 52 microcontroller output PWM speed dc motor.The positive &negative, realize motor 390v adjustable, automatic can realize feedback adjustment speed setting.
motor-Speed-control--Matlab
- 直流交流电机的调速,包括开环调速、闭环调速,矢量调速,直接转矩调速,转速频率差调速,附件为其部分源代码-DC-AC motor speed control, including the open-loop speed control, closed loop speed control, Vector Control, Direct Torque Control, Speed governor frequency difference, annex part of t
Dc-motor-speed-control
- 对应的电机接口需用杜邦线连接到uln2003电机控制端 使用5V-12V 小功率电机皆可 2个按键分别加速和减速-DuPont corresponding motor interface cable required to uln2003 motor control side using 5V-12V low power motor can be two key acceleration and deceleration, respectively,
31Dc-motor-drive-and-speed
- 直流电机测速,实现正反转控制、PWM转速控制,测速、1602显示。开发环境为KEIL 4-Dc motor speed, realize positive &negative control, PWM speed control, guns, 1602 display
76_PID
- 电机转速控制器采用PID技术,可以调节直流电动机转速-Motor speed controller uses PID technology, can adjust the speed of DC motor
Three-phase-brushless-DC-motor
- 三相无刷直流电机的控制程序,里面详细的介绍了控制电机转速,控制电机正反转的程序-Three-phase brushless DC motor control program, which detail the control of motor speed, reversing motor control program
motor
- 直流电机调速控制 直流电机调速控制 直流电机调速控制-DC motor speed control DC motor speed control DC motor speed control
Motor
- 实现对直流无刷电机转速的控制程序,可通过键盘控制启停和转向并得到实时转速-Achieve the brushless DC motor speed control program, start and stop can be controlled through the keyboard and get real-time speed and steering
(www.entrance-exam.net)-GEN.-APP
- verilog hdl code for speed control of dc motor
motor
- Mega16的PID算法控制直流电机转速仿真及程序,增量式和位置式算法都有,虽然在Proteus中的电机调速基本只要比例环节就够了,但是程序算法对初识PID的新手还是有参考价值-The Mega16 the PID algorithm to control the DC motor speed simulation and procedures, incremental and positional algorithms have, in Proteus motor speed basic pr
PWM-PID-motor
- 运用PID调节器,实现直流电机在带动负载的情况下也能稳定的运行。运用A/D转换芯片将滑动变阻器的模拟电压转换为数字量作为控制直流电机速度的给定值;用压控振荡器模拟直流电机的运行(电压高-转速高-脉冲多),单片机在单位时间内对脉冲计数作为电机速度的检测值;应用数字PID模型作单片机控制编程,其中P、I、D参数可按键输入并用LED数码显示;单片机PWM调宽输出作为输出值,开关驱动、电子滤波控制模拟电机(压控振荡器)实现对直流电机的PID调压调速功能。-Use of the PID controlle