搜索资源列表
zhuangtaizhishi
- 多路开关状态指示 如图4.3.1所示，AT89S51单片机的P1.0－P1.3接四个发光二极管L1－L4，P1.4－P1.7接了四个开关K1－K4，编程将开关的状态反映到发光二极管上。（开关闭合，对应的灯亮，开关断开，对应的灯灭）。 -multiple switch state instructions shown in Figure 4.3.1. AT89S51 SCM P1.0 - P1.3 then four LED L1 - L4, P1.4 - P1.7 then sw
OpenGLWork
- 这个是老师留的作业，用OpenGL方针一个机械手开/关一个灯泡-the teachers to stay the operation of a principle with OpenGL manipulator on / off a light bulb
rushing
- A six people s rushing replies an implement, use some s switches in toggle switch K0 ~ K5 is that ON accomplishes when rushing to reply button , nobody rush to answer, 6 numerical code circulation takes turns at demonstrating 1 ~ 6 (horse races) , wh
tracing
- 本工程是一个关于计算机图形光线跟踪的算法，由于是本人教早的作品所以只做了球型物体的光线跟踪以及物体的高亮设计、环境光设计、光线反射等设置。-this is a project on computer graphics ray tracing algorithm Since I work in the morning so the ball off the light in tracking objects and objects highlighted design, Optical desig
timer-to-LED1
- 基于研旭DSP28335基础版编写的例程，通过定时器控制LED1的亮灭，定时时间可调-Based on research Asahi DSP28335 Basic routines written by timer control LED1 light off, adjustable timing
DA-_LED
- 单片机的入门程序，DA转换模块控制LED灯的亮灭-SCM entry procedures, DA converter module controls the LED light off
breath
- 基于51单片机的使用PWM调制的呼吸灯，可随正常人的呼吸亮灭。-51 microcontroller-based PWM modulation using breathing light, can light off with normal breathing.
DLAJ_51
- 用51单片机按键输入LED的亮灭 用51单片机按键输入LED的亮灭-51 single input button LED light off
sw_debounce
- 当三个独立按键的某一个被按下后，相应的LED被点亮；再次按下后，LED熄灭，按键控制LED亮灭 -When one of the three independent keys is pressed, the corresponding LED is lit once again, after the LED is out, the button control LED light off
LED
- 基于52单片机的广州塔LED灯程序，控制亮灭-Based on 52 single-chip LED lights Guangzhou Tower program to control light off
LED
- 用proteus仿真的电路图，甲单片机控制乙单片机led的亮灭，程序源码和仿真图都在压缩包里面了-With Proteus Simulation of the circuit diagram, a single chip microcomputer control LED light off, the program source code and Simulation of the compression package inside the
KEY2LED_USART
- 该C程序基于STM8L15x系列微处理器，在IAR开发环境下编译，实际能够实现按键控制LED亮灭，串口接收发送数据的功能。很经典的STM8入门例程，供新手学习。-The C program is based STM8L15x family of microprocessors, in the IAR compiler development environment, to achieve real keys to control LED light off, the function seria
1.IO-Led-on-or-off
- IO控制Led亮灭 基于CC2530单片机-IO control Led light out based on CC2530 MCU
3.key-control-led-on-or-off
- 按键控制LED亮灭，LED1 LED3均可使用-Button control LED light out, LED3 LED1 can be used
USART1-_led
- stm32嵌入式系统串口通信源码，可连接蓝牙，发送字符控制相应引脚的灯的亮灭-STM32 embedded system serial communication source code, can be connected to Bluetooth, send characters to control the corresponding pin of the lamp light off
Sound-and-light---temperature-alarm
- 1、温度显示 声光型数字温度报警器是基于单片机控制的数字化功能平台。以单片机为核心控制的电路，结合数码管及其它元器件的使用，温度传感器接收温度，通过电路，使它能在数码管上显示。 2、温度报警 通过C语言编写的程序来控制单片机的运行，设置上限温度，当温度达到所设定的温度时，蜂鸣器就接通，发出声音，提示温度超过所设定。 3．报警解除 当实际温度超过所设定的温度时，蜂鸣器报警，如果要切断报警，可以做出终止报警，但是温度还在数码管上显示。 -1, temperature
light-emitting
- 8个发光二极管以间隔100ms来回流动两次，同时蜂鸣器发声,然后全部熄灭，间隔300ms全部闪烁两次。-8 light-emitting diodes to flow back and forth at intervals of 100ms, while the buzzer sound, and then all off, all 300ms intervals flash twice.
indicator-light
- 按钮的状态指示灯的运用，按钮为打开状态时，则指示灯亮；按钮为关闭状态时，则指示灯灭。-Status lights use a button, the button is turned on, the indicator light button is off, the lights off.
6_key_test
- 用Verilog实现的按键控制LED灯，按下按键，对应的灯亮，再按一下灯灭。-Use Verilog to achieve the key to control the LED lights, press the button, the corresponding light, and then click the light off.
matlab之红绿灯的监测以及亮灭
- 将亮的红绿灯圈出来_并在圈内显示红绿灯颜色 图像找到红绿灯位置_判断红绿灯哪个亮 指定位置_最大灰度值_判断亮灭(Circle the bright traffic lights _ and display the traffic lights in the circle Image find traffic light position _ judge which light is green Specify position _ maximum gray value _ judgm