搜索资源列表
RS_5_3_GF256
- 用于NAND FLASH CONTROLLER 中的 ecc 各个模块VHDL代码-NAND FLASH CONTROLLER for ecc modules in VHDL code
fpga-dm9000a
- 一个项目工程,硬件包含XINLINX FPGA,配置FLASH,串口,SDRAM,与以太网芯片DM9000A,实现数据采集,以太网传输,电路验证完全正确,请放心使用,SPARTAN 3E 的BGA引脚320个,不容易布板,可以参考使用的。要FPGA实现网络通信也可以参考电路,B因为产品升级了所以公开原来的电路的。 -A project engineering, hardware contains XINLINX FPGA, configuration FLASH, serial port, SD
DE2_NIOS_Lite_12_flash
- 实现如何在Nios II对Flash进行读写 [SOPC、Nios II、DE2] -Introduce how to read and write the Flash using Nios II[SOPC、Nios II、DE2]
NandFlash-FPGA-controller(ECC)
- 该压缩包包括NAND FLASH(美光)的FPGA控制器的原理及VHDL源码,非常具有参考价值。-The archive includes NAND FLASH (Micron) the principle of the FPGA and VHDL source code control, very valuable reference.
ECC_1bit
- 1bit的用于nand flash的纠错码编解码器。vhdl-1bit ecc for nand flash vhdl
SPI_controller
- SPI serial flash ROM的verilog源代码, 针对winbond W25x16,已经经过逻辑验证,并实际用在芯片设计中,作为一个模块,正常工作.-SPI serial flash ROM in verilog source code for winbond W25x16, logic has been verified, and actually used in chip design, as a module to work.
Am29lv160d
- 在逻辑的系统仿真中使用的FLASH模型(AMD的Am29lv160d),包括VHDL代码文件和verilog代码文件和testbench,并且有相应的pdf说明文档。-In the logic system used in FLASH simulation model (AMD s Am29lv160d), including VHDL and Verilog source code files of documents and testbench, and the corresponding
flash_memory
- VHDL model for a NOR Flash
M25P32_VG_12_50MHZ
- Serail Nor Flash Memory Model
NANDFLASH
- 用VHDL开发的NANDFLASH的读写程序,给出 NANDFLASH的时序正确的读写-NANDFLASH developed using VHDL to read and write the procedures, timing NANDFLASH give the correct reading and writing
PROM
- 在FPGA设计中,从配置PROM/FLASH读取用户数据-PROM
123456
- NAND型Flash在大容量存储回放系统中的应用-Flash
niossramflash
- 在altera FPGA ep3c25器件上实现niosii+sram+flash-Altera FPGA ep3c25 in devices to achieve niosii+ sram+ flash
03.EDK8.2
- 使用xilinx virtex4芯片,设计环境为EDK,其中包含uart,片外sram操作,flash操作,DDR SDRAM操作,MAC自发自收,audio,video等试验-Xilinx virtex4 use chip design environment for the EDK, which contains the uart, chip sram operation, flash operation, DDR SDRAM operation, MAC spontaneous self-
Fingerprint_Identify
- 本项目名称是:基于FPGA的指纹识别模块设计。 主要内容为:本模块采用xilinx公司的Spartan 3E系列XC3S500E 型FPGA作为核心控制芯片,通过富士通公司的MFS300滑动式电容指纹传感器对指纹图象进行提取,然后对提取的指纹图像进行灰度滤波、图像增强、二值化、二值去噪、细化等预处理,得到清晰的指纹图象,再从清晰的指纹图象中提取指纹特征点,存入外部FLASH作为建档模板。指纹比对时,采用同样的方法获得清晰的指纹图像,建立比对模板,然后将比对模板与建档模板利用点模式匹配
wb_flash_latest[1].tar
- flash 控制器,用verilog描述,希望对大家有帮助-flash controller!
NAND_IP
- Nand flash VHDL code and Nand flash verilog code
pico_code
- pico blaze VHDL code for write to micro SD flash with spi protocol
usb_fpga_1_2_latest.tar
- USB2.0的FPGA内核,使其可以通过FPGA控制CY公司出品的CY7C68013USB微控制器,对USB设备进行读写操作。-• Xilinx Spartan-3 XC3S400 FPGA • High-Speed (480 MBit/s) USB interface via Mini-USB connector (B-type) • Cypress CY7C68013A/14A EZ-USB-Microcontroller • 60 G
nand_flash_ctl
- FPGA flash 控制读写程序 与mcu相连-FPGA flash control is connected to read and write procedures and mcu