搜索资源列表
UARTRXTX
- MSP430f449的max232的TX与RX问题解决-MSP430f449 the max232' s problem-solving TX and RX
BNQC-JX48-RX(MOS)20100903
- PIC16F877A用于驱动直流马达,PWM控制,过压检测,过流检测;-PIC16F877A
Rx
- 52 单片机温湿度使用很好的,自己写的哦!-52 temperature and humidity with good, to write, oh!
CCxx10--rx
- CCXX10 接收程序 功率级别 休眠级别 报警,收发器地址-CCXX10 received power level hibernation program level alarm, the transceiver address
rx
- 基于新华龙单片机对2401无线发射模块的编程代码-Hualong microcontroller based on the new wireless transmitter module for 2401 programming code
S12P-SCI-Tx-and-Rx
- freescale mc9s12p timer example source
Range-Demo-Plus-RX-NCB
- 飞思卡尔公司在无线传感器网络中SMAC的例程,主要节点的接收功能-Freescale SMAC in wireless sensor networks in the routine, the main reception node
1MHZ-code
- * RECEIVER * * CC430 RF Code Example - TX and RX (fixed packet length =< FIFO size)
msp430-CC1100-SPI
- MSP430 CC1100 SPI TX RX-MSP430 CC1100 SPI
rf12_code_cn11
- 学习RF12,TX,RX无线通讯产品,主要应用在遥控方面-Learning RF12, TX, RX wireless communications products, mainly used in remote areas
F340_uart
- 本程序是通过F340的uart0与PC进行串口通讯的例程,具体实现为当F340收 *从PC传来的数据后将数据原样回发给PC机 ,端口为RX=P0.5,TX=P0.4-This program is through the F340' s uart0 serial communication with PC for a routine, concrete realization of the closing* When the F340 data coming from the PC a
rx
- nrf2401无线 计分牌演示程序\接收端代码,是单片机C语言程序,通过模块NRF实现无线计分,这是接收端程序-nrf2401 Wireless Wireless scoreboard demo \ receiver code, microcontroller C programming language, through the wireless module NRF points, which is the receiver program
2p4-rx
- 2.4 wireless assembly code
can-rx-and-tx
- can信息收发代码,简单实用!适用于初学者!-can receive and trammit codes.it is simple and good!
EXAMPLE4.15
- PIC16887A单片机一个双机通信,2个单片机异步串行通信接口相连方式为:RX和TX交叉对接,左边的单片机U1,每按下按键S1就发送一个字节数,从0x20开始发送,每送一个数据,此数加1.发送的同时在D口上输出。右边单片机U2为接收状态,采用中断方式,如有接收中断,则进入中断,将接收到的数直接在D口上输出-PIC16887A a two-machine communications microcontroller, two asynchronous serial communication i
TX-RX-TEST
- 24L01程序,好用哦,基于msp430-24L01 program, easy to use Oh, based on the msp430
chipscope_Tx-Rx
- chipscope analysis of mini uart module including counter for spartan 3e
TestNTC
- 计算被测量电阻。只做比较,不作计算。 计算公式:Rx = Rf * (Tx/Tf) Rx为被测电阻 Rf为已知电阻,Rf=10K Tx为被测电阻对电容C放电的计数值,为16位数 Tf为被测电阻对电容C放电的计数值,为16位数 查温度特性表(NTC型号为:CWF2-473F-3950K,大亚科技制造): 下限温度5摄氏度时电阻为121545.44欧,即121.54544K 换算为:Tx/Tf=Rx/Rf=12.154544 扩大1000倍后结果
xianlutongduanqi
- 线路通断检测器的设计: 1.用压电陶瓷蜂鸣片作为电声元件。 2.用两根导线作为测试探针 3.线路通断是通过测试电阻的大小来判断,有以下三种情况: (1)若150Ω<Rx<900Ω,则蜂鸣片不发出声响。 (2)若Rx>900Ω或者Rx<150Ω,则蜂鸣片发出间歇式的滴-滴声响。 以上各临界阻值(150Ω和900Ω),允许误差±10% 4.+15V直流稳压电源需要设计。 -Line-off detector design: 1. Piezo
fet140_uart01_19200_2
- MSP430串口0通信,回显收到的字符。波特率19200.-USART0, UART 19200 Echo ISR, XT2 HF XTAL ACLK. Echo a received character, RX ISR used. Normal mode is LPM0,USART0 RX interrupt triggers TX Echo. Though not required, MCLK = XT2.ACLK = n/a, MCLK = SMCLK = UCLK0 = XT2 = 8M