搜索资源列表
em78LED
- 数码管LED显示 PORT6输出动作的控制，而且外部接有一推动8个七段显示器的电路。编写一程序在8个七段显示器上轮流显示1,2,3,4,5,6,7,8。 -Digital tube LED display output PORT6 movement control, and external access there is a push paragraph 8 of the circuit monitors. The development of a procedure in parag
2
- 只要流程及功能：判断按键是否按下、是否弹 起、是否多按键按下、去抖、按键值送给KEYIN-As long as the flow and function: to determine whether the button press, whether the shells starting Whether or not many buttons pressed, go shake, push the value of a gift KEYIN
push_100kHz
- this is arm code for push 100kHz
led
- 是控制LED闪烁发光的简单例程。该程序实际上是实用工程模板Demo的一个应用，直接从main( )函数开始编写。 在main( )函数的前面，定义了LED所在的GPIO端口和管脚。在main( )里，首先定义了一个变量ulClock，在调用函数clockInit( )时被初始化为当前的系统时钟频率，在后面对库函数SysCtlDelay( )调用时会用到该变量。 控制LED分3步走：调用函数SysCtlPeriEnable( )使能LED所在的GPIO模块，调用函数GPIOPinTypeO
shirenqiangdaqi
- （1）抢答器同时供4名选手比赛，分别用4个按钮S1 ～ S4表示； （2）设置一个系统清除和抢答控制开关S5，该开关由主持人控制； （3）抢答器具有锁存与显示功能。即选手按动按钮，锁存相应的编号，选手抢答实行优先锁存，优先抢答选手的编号一直保持到主持人将系统清除。 -(1) Answer 4 simultaneous players for the game, with four buttons, respectively, S1 ~ S4 that (2) to set up a
AT89C51
- 理工大学的一篇学士论文，个人感觉值得借鉴。用单片机作控制系统。干式变压器温度控制系统是维护干式变压器运行的重要部件，能有效防止变压器温升过高而引发事故，还能促进变电站的科学管理，通过降低温度实现变压器的经济运行，其工作可靠性的高低和操作是否方便将直接影响到干式变压器的运行质量。本设计从系统功能、硬件结构和程序设计等方面介绍了一种基于AT89C51单片机为核心、Pt100铂电阻为温度传感器并以NE555定时器作为A/D转换器，拥有看门狗电路、LED显示及简单的按键系统构成的干式变压器温度检测仪。
code
- UCOS_II在摩托罗拉单片机上的移植，包括在bank内存中的移植，即要压战ppage- UCOS_II transplant to Motorola, including the memory bank of the transplant, which was to push ppage
MCS51Sample
- 51单片机开发的几十个实例，使用时直接在源代码后附入所需的子程序，直接编译即可（注意对部分寄存器进行压栈保护）-51 single-chip developed by dozens of examples, when used directly in the source code attached to the required subroutine, the compiler can direct (the attention of some to push the protection o
CforEmbeddedSystems
- 嵌入式系统的C程序设计，对刚开始入门的人很有用啊！-This book provides a complete intermediate-level discussion of microcontroller programming using the C programming language. It covers both the adaptations to C necessary for targeting an embedded environment, and the co
main
- Source code for MCC18 compiler. Runs BiPolar Stepper motor interfaced to PORTD when an interrupt is generated via PORTB 0 Pin by a push button.
application_note_source_code___creating_a_sample_
- This example uses the 2131 dev board s push buttons for limited 2 button mouse/2 button keyboard functionality and is based on the EZ-USB firmware frameworks.
H240NEWFD
- 使用51/Keil C撰寫touch panel的測試程式(畫線/報座標/方格按壓測試等等)-writing touch panel test program(draw line/report coordinates/push test) by keil c
s3esk_rotary_encoder_interface
- spartan-3e starter board 旋转开关-spartan-3e starter board rotary push Button
C8051F060_PWM
- 基于C8051F060的PWM产生程序。 采用软件定时器完成，使用普通口线输出，输出为推挽输出，上升沿和下降沿陡峭并存在过充。提供PWM波频率调整、占空比调整、双路输出PWM波死区时间调整功能。-The PWM generation process based on the C8051F060. Completed using the software timer, use the normal port line output, the output of push-pull output
key_LED
- 在2440板子上实现的一个简单的按键控制灯亮灯灭的程序-In 2440 the board implemented on a simple push-button control of lights switched on eradication programs
game
- 小游戏规则： led(0 to 3)是按一定规律不断发亮，每次只有一个灯亮，每个灯都和我们BASYS板上的四个按钮中的一个对应着，当Led(0 to 3)中的灯亮时，我们要按对相应的按钮时候，在led(4 to 7)中对应的按钮就会亮起，并且八段码显示的数字也相应的加上一，要是按错了led（4 to 7）灯不亮，且显示数字减1。-A small game in which LED(0 to 3) lights in turn. Just one LED turns on each tim
keyboard
- DSP编程简单的按键程序,采用4*4键盘,实现LED数码管显示数据-DSP programming simple push-button procedure, using 4* 4 keypad, LED digital tube display data to achieve
pretaiz
- this for car security it cut electric circuit if don`t push secret button at 5 seconds from engine starts.If establish a fact unauthorized interference then blocked electric circuit for engine start.-this is for car security it cut electric circuit i
fuwo
- 控制机器人完成俯卧撑动作，机器人关节为AVR单片机-Control the robot moves to complete push-ups, for the AVR MCU Robot
FanControlSystem
- This a smart ventilator fan system. When it detects the presence of a user, it spins in one direction and blows the air towards the user, very much like an electric fan. However, it starts at a particular lower speed and increase to the top speed onl