搜索资源列表
24LOI-1to6-sent-receive
- 24lO1 多对一 6对1 数据发送接收配置-24lO1 1 to 6 sent receive
315MHz-send--receive
- 基于315MHz无线收发模块的单片机收发程序，比较简单-315mHz send receive
Q2406
- Q2406gprs/gsm模块的收发短信程序，已经通过测试-Send and receive SMS Q2406gprs/gsm process module has passed the test
communication-USART-IrDA-transmit-receive-mode
- This example provides a basic communication USART3 IrDA receive/transmit mode. Four leds are used to show which byte is received/transmit.
receive-and-show
- 通过串口接收数据并通过LED显示出来。很完整的代码，已经实际应用过，比较简单，包括了定时，延时，按键等，代码说明也写的很详细-Receive the data through serial interface and show it by led
send-and-receive-data-DMA-interrupt
- 采用DMA中断的方式收发数据 -Used to send and receive data DMA interruptUsed to send and receive data DMA interrupt
receive
- 2401的接受程序，用来接收发送端发来的数据。并且显示到数码管上-2401 of the acceptance procedure, used to receive data sent by the sender. And displays to digital tube
msp430nRF24L01-SPI-receive-transfer
- 用msp430f149实现的nrf2401的收发程序-Msp430f149 achieved with the program to send and receive nrf2401
Serial-port-to-receive-test
- 此压缩包为一个串口接收实验，通过单片机的串口实现信息的接收，适合初学者自觉-This archive is a serial receiver experiment, through the microcontroller serial port to receive the information for beginners and consciously
Serial-port-to-receive-test
- 串口接收试验，单片机的使用时用到-Serial port to receive test
receive
- IA4420的接收程序，单片机是PIC16F690-receive code of IA4420,single chip is PIC16F690
485-automatically-send-and-receive
- 485接口自动收发通信 52单片机实现485的自动收发通信-485 automatically send and receive communications 52 MCU 485 automatic send and receive communications
51-string-receive-code
- 51接收字符串演示程序.rar 单片机可以接受超长字符串，当然字符串来自PC，其他的也可以， 收到后再原封不动的发回来，本代码12MHz,波特率为4800，有11.0592M的话可以更完美，（9600下可以误差0 ，当然的你自己去改本代码） 本代码现在可以在4800,12M下正确发送94个单字字符 （注：第64个支付被丢后面的前移一个字符，因为12M下波特率不是标准的4800） 或31个双字节字符（汉字）。-51 to receive the string demo prog
receive-mms
- 本程序是用于单片机与GPRS无线发射模块的通信，单片机通过串口控制GPRS模块接收一条彩信，适用于初学者-The program is used for the communication between MCU and GPRS module .MCU can control the module and make the module receive a mms.It suitable for freshmen to refer
MSP430-IR-transmit-receive
- 利用CC430X513X的定时器来收发红外信号。提供源程序的学习和发送程序。-The use of timer CC430X513X to send and receive infrared signals. Source of learning and sending program.
bluetooth-temp---receive
- 51单片机通过18B20温度传感器采集温度数据，通过单片机串口接收指令，然后通过串口发出。串口接蓝牙模块，实现了温度在手机上的显示。-51 single-chip temperature data collected by 18B20 temperature sensor, through the microcontroller serial receive instruction, and then sent through the serial port. Serial port to ac
MCU-Serial-receive-data
- 通过串口助手要接受字符串或一组数据需要在单片机端开辟一个缓冲区，否则可能丢失数据。以下程序是较为通用的串口收发例程，开辟一个16字节的缓冲区，两个指针，一个存数指针，一个取数指针，两指针相等，证明没有新的接收数据。-To accept a string or a set of data through the serial port assistant on the microcontroller side to open up a buffer, or data may be lost. Th
A-serial-port-to-send-and-receive
- 此代码为STM32单片机的串口发送与接收的代码，可通过串口小工具来验证调试，经过验证切实可行。-This code for the STM32 microcontroller serial port to send and receive the code, can through the serial port small tool to verify the debugging, proven feasible.
serial-receive-and-send
- 单片机串口收发程序，程序简洁易懂，非常适合初学者学习。-receive and send function of single chip
serial-assistants--receive--data
- 旋转电位器，串口助手将收到不同的数据，在PC机上显示-Rotary potentiometer, serial assistants will receive different data