搜索资源列表
LS_soft
- 5402控制88796网卡的程序，用于网络开发。提供了网络发送接受等功能-5402 88796 Ethernet control procedures for network development. Providing the network send and receive functions
DSP_SCI_C
- DSP2407实现SCI串口通信的C语言源代码。 分别使用2个中断实现串口的接收/发送。-DSP2407 achieve SCI serial communication C language source code. The use of two separate Serial interrupted the receive / transmit.
CAN2.0
- 关于can总线2.0的发送和接受程序,经项目验证通过,具有极大的参考价值.-2.0 on the bus can send and receive procedures, certification by the project, is of great reference value.
I2CRCVint
- dsp中关于I2C 的接收数据的操作，通过对eeprom进行读写，达到数据的交流。-dsp on the I2C receive data, the operation of EEPROM write, to achieve the exchange of data.
LP_DMA_C
- 老外写的TS201 LinkPort DMA发送/接收程序，学TigerSharc的可以看看。-foreigner wrote TS-201 LinkPort DMA Send / Receive process, TigerSharc the school can look at.
receive
- DSP实现TL16C550及RS232的串口传输（接收端）
用DSP进行语音压缩的一个开发实例
- 整个一个实际的例子.可以从中获得DSP编程与开发的启示.-throughout an actual example. DSP will be able to receive programming and the development of inspiration.
2812-qep-zhengjiao 2812片上qep使用例程
- 2812片上qep使用例程，使用的是qep1、qep2来完成正交编码检测的。运行后查看speed即为电机转动1s产生的脉冲数。脉冲信号需要接到qep1、qep2引脚。-2812 on qep use routines, using qep1, qep2 to complete the orthogonal encoding detection. After viewing the motor running speed is the number of pulses generated by r
F2812_SCI02 PC机串口调试助手
- F2812 SCI与PC机串口调试助手以收发中断方式实现收发数据。（CCS3.3开发环境） 功能：使用SCIA模块和PC机进行串口通信，等待PC机上的串口调试软件向DSP发送"hellodsp"，DSP接收到上位机发送的数据之后，将这些数据发回PC机，显示在串口调试软件中。 说 明：本实验中SCIA模块的发送和接收采用中断方式实现，空闲线模式波特率为19200，通信数据格式为1位停止位，8位数据位，无校验位-F2812 SCI and the PC serial port r
SCIA模块的发送和接收采用中断方式实现
- 本实验中SCIA模块的发送和接收采用中断方式实现，空闲线模式波特率为19200， * 通信数据格式为1位停止位，8位数据位，无校验位-This experiment SCIA transmit and receive modules achieved by interrupt, idle line mode the baud rate is 19200,* communication data format is 1 stop bit, 8 data bits, no parity
bf53x_sport
- ADI DSP blackfin 系列处理器 BF533 SPORT接口的使用，SPORT接口是BF533常用于音频数据的传输，代码实现了采用SPORT接口传输和接收数据。-ADI DSP blackfin BF533 SPORT family of processors to use interface, SPORT BF533 interface is commonly used in audio data transmission, the code implements the use
CAN_RX
- F2812 CAN总线接收数据（CCS3.3开发环境下） 实验目的:通过外部其他CAN设备给Super2812发送数据，了解CAN总线的设置和通讯过程，请尤其注意ID的设置 实验说明:将MBOX16设置为接收模式，并采用中断的方式接收数据 实验结果:可以观察变量Rec_h，Rec_l,查看收到的数据-F2812 CAN-bus receiving data (CCS3.3 development environment) Purpose of the experiment:
TMSC3206416串行数据通讯代码
- TMSC3206416串行数据通讯代码，其中包括寄存器的配置，EDMA的配置，及接收数据和发送数据的代码-TMSC3206416 serial data communication codes, including the configuration register, EDMA configuration, send and receive data and code data
IO.rar
- 由拨码开关通过数据线D0-D7向DSP输入0-255数据，DSP收到数据后通过D8-D15向发送收到数据的到发光二极管进行显示,From the allocation of key switches through the data lines D0-D7 to the DSP input 0-255 data, DSP receive data through the D8-D15 to send received data to the light-emitting diode displa
ECAN
- 这是一个CAN总线应用，CAN总线接受和发送的程序-This is an application of CAN bus, CAN bus, the procedures to receive and send
Spi01
- 2812实现SPI的回送测试模式，SPI自发自收，发送和接收采用查询方式实现，将SPISIMO和SPISOMI两个引脚内部短接，实现自发自收模式。SPI将0-99这100个数字逐个发出，然后逐个接收存入Spi_VarRx[]。-2812 to implement the SPI loopback test mode, SPI spontaneous self-closing, send and receive be achieved using query will SPISIMO and SP
mcbsp_loopback
- DSP28335的MCBSP接口的驱动程序，类似SPI口的功能，可进行数据的收发-The DSP28335 MCBSP interface driver, similar to the SPI port can send and receive data
11_CANRX
- DSP2812 ecan总线只接收数据例程-DSP2812 ecan bus receive only data routines
Main
- 基于DSP2407的CAN通讯C程序 CAN的接受和发送修改后 均可实现-DSP2407 based on the CAN communication C program to receive and send CAN
CAN-send-and-receive-data
- CAN总线通信程序源码，包括CAN通信主程序设计，CAN控制器初始化程序、CAN发送程序和CAN接收程序-CAN bus communication program design, including CAN bus communication of the main program. Including the CAN controller initialization, CAN send program and CAN receive procedures