搜索资源列表
GWDVP3
- 利用51单片机,开发的一个专门电子竞技用的最小系统板源代码。-use 51 microcontroller, the development of a competitive specialized electronic systems with the smallest plate source.
vhdl_lcd
- 使用C语言与VHDL实现 液晶显示控制器示例使用说明 使用模块有:单片机模块、液晶显示模块。 使用步骤: 1. 打开电源+5V。 2. 信号连接,按下表将1K30信号与实际模块连接好。 3. 1K30板连接好并口线,并将程序加载。 4. 液晶屏上将显示一幅图像。 -use C language and VHDL LCD controller using examples of the use of modules : SCM modules, LCD disp
调试程序
- 汽车号牌识别系统,还没有结束,因为没有程序了,所以来凑个树-vehicle license plate recognition system, is not over yet, because no procedures, so to take care of 000 trees
STD
- arm板的开发试验,从简单到复杂,初学者必看-arm plate development and testing, from simple to complex, beginners Watchable
Light_On_Turn
- 一个用谢刚(www.xieg-gang.com)实验板实现流水灯的C代码陈雪。直接烧录入单片机就可运行。谢刚本身没有提供C51的源代码。-a used Xie Gang (www.xieg - gang.com) experimental plate lights to the water Chen C code. Direct Input MCU can burn operation. Xie Gang C51 itself did not provide the source code.
flashtest
- 一个测试凌阳61板中FLASH的程序,用汇报和C混合编写的-a test Sunplus 61 plate FLASH the procedures used to report and the preparation of the hybrid C
nRF24E1编程下载板相关程序
- nRF24E1编程下载板是我们自行开发的简易无线通信模块nRF24E1的在线下载板,使用方便。 nRF24E1编程下载板源程序包括上位机程序、单片机固件程序和nRF24E1内51核控制程序, 分别存放在“上位机程序”、“AT89S52”和“nRF24E1”三个文件夹内。 “上位机程序”内有应用软件download.exe。 “AT89S52”内有单片机固件源程序download.c,可以直接编译连接生成下载文件,下载到目标单片机AT89S52中。 “nRF24E1”内有控制n
danbaizhishuijie
- 温度传感器18B20汇编程序,采用器件默认的12位转化,最大转化时间750微秒 可以将检测到的温度直接显示到AT89C51开发实验板的两个数码管上 显示温度00到99度,很准确哦~~无需校正!-temperature sensor 18B20 assembler, using the default device into 12, the largest 750 microsecond conversion time can be detected by a direct indic
12864_chs
- 此程序为单片机常用的128*64的液晶屏的测试程序(为一实验板配套程序)-this procedure commonly used for the MCU 64 * 128 LCD screen test procedure (for a plate supporting experimental procedure)
RCL-Test
- 凌阳61单片机实现RCL,由C语言编写,凌阳61板实现功能-Sunplus 61 MCU RCL from the C language, Sunplus 61 plate function
764demo
- LPC760单片机功能测试程序 本测试板是专门针对Philips公司的低功耗单片机P87LPC762而设计,用于测试P87LPC762多种功能-LPC760 MCU function testing procedures of the test plate is targeted at the Philips low power SCM P87LPC762 consumption and design, testing for a variety of functions P87LPC762
RS232-CAN
- 用Freescale的8位单片机做的RS232-CAN的通讯转换板.包含固件程序,原理图,PCB图和一个说明文件.-with Freescale's 8-bit MCU do RS232-CAN communication switch plate. Includes firmware procedures, drawings, PCB map and a note.
20069920137102
- 89S52加USBD12模拟的一个U盘(源码+原理图+实物照片) Computer00 发表于 2006-3-3 14:09:00 USB-D12文件包下载.rar 这是一个用89S52加PDIUSBD12模拟的一个U盘,里面涉及到USB接口,USB大容量存储设备,FAT16文件系统等内容。插入电脑后,可显示移动磁盘盘符及一个文本文件。 需要说明一下的是,这个包中的原理图,IDE接口部分、74HC573、以及RS232串口等部分,是作为这个实验板的一
CY4615B_revC
- 赛普拉斯CY68300开发板的详细资料及原理图、源程序-plate ware development CY68300 detailed information and drawings, source code
romote_dianming
- 凌阳61板单片机应用,用到两块61板和一块以太网模组,模组和一块61板实现以太网驱动,另一块61板实现音频播放及辨识-Sunplus 61 plate SCM application, used two plates and a 61 Ethernet module 61 modules and a plate Ethernet driver and the other a 61 plate achieve literacy and Audio Player
61syzsm
- 61板实验指导书源代码,对于学习61单片机真是不可多得的好东西哈~强烈要求给我多加点数,因为这个里面包括了10多个源代码-61 plate guide books source code, MCU 61 for the study is a very good thing Kazakhstan ~ I strongly demand for more points, This includes the more than 10 source code
61ksm1
- 《61板课程设计指导书一》源代码,里面10多个非常优秀的源代码,大家谁还需要单片机的程序email我就可以拉 -"61 plate curriculum design guide book a" source code, where more than 10 outstanding source code, SCM everyone who needs the procedure I can email Rafah
yeweiji
- 用C51写的单片机程序,在Wave600环境下测试通过,利用平板电容器测试液位。-with C51 microcontroller written procedures, Wave600 environment in the test, Capacitor plate test level.
SLDIY028AICCAVR
- 这里有11个用ICCAVR开发的源代码,经DEMO板调试后已经通过.-here with a 11 ICCAVR development of the source code, DEMO plate after debugging has been passed.
Jlink-adapter-plate-Chinese-documentation
- Jlink转接板中文说明文档 针对不同的针数接口-Jlink adapter plate Chinese documentation for different pin count interface