搜索资源列表
firmwareVna
- 矢量分析仪cypress an2135源码-vector analyzer cypress an2135 FOSS
06_DesignExploration
- This lab exercise will cover the use of AccelDSP’s design exploration capabilities that include mapping variables to memory and unrolling loop and vector operations. You will learn how to create different hardware architectures without modifying the
xlab001
- 在室內環境中可結合式子母機器人系統，子機為一多功能平台，可放置各種家庭所需之設備，而母機為一輪式機器人，經由兩者的結合，可提供高機動性與多功能的服務。在結合的技術面，傳統的吸塵器機器人與充電站之間的導航系統使用紅外線感測作為依據，當兩者間有障礙物阻擋時，紅外線感測器導航系統將會失效。因此本系統利用聲源方向做為機器人決定移動方向的依據，由於聲波傳遞的特性，即使在有障礙物的情況下，依然可以有效地偵測。此外，在移動的過程中，本系統利用光流偵測法判斷是否遭遇障礙物或是利用Support Vector M
FOC_of_PMSM
- keil下开发的永磁同步电机矢量控制程序，控制芯片是infineon XC164。-keil developed permanent magnet synchronous motor vector control procedures, control chip is infineon XC164.
irq
- arm7TDMI irq 44B0 向量中断实验程序-arm7TDMI irq 44B0 experimental procedure interrupt vector
mars
- 基于MARS的无速度传感器矢量控制系统研究-MARS-based speed sensorless vector control system
simulink
- 基于MARS的PMSM无速度传感器矢量控制系统研究-MARS-based speed sensorless PMSM vector control system
Desktop
- IC AT89C51 is a low-power, high-performance, 8-bit microcontroller with 8 kB of Flash programmable and eras-able read-only memory (EPEROM),256 bytes of RAM,32 input/output (I/O)lines, three 16-bit timers/counters, a six-vector two-level interrupt a
ccp
- 汽车CCP功能实现，VECTOR官方下载的实现代码-Automotive CCP functions
Simulation-of-Speed-Sensor-less-Control-of-PMSM.r
- Permanent magnet synchronous motors (PMSM) are appropriate for applications with load-independent speeds or synchronous operation with high accuracy under defined speed. In this paper analysis the structure and equations of the PMSM, direct torque
msp430x20x3_sd16A_01_with_trap_ISR
- MSP430F20x3 Demo - SD16A, Sample A1+ Continuously, Set P1.0 if > 0.3V // // Descr iption: A continuous single-ended sample is made on A1+ using internal // VRef Unipolar output format used. // Inside of SD16 ISR, if A1 > 1/2VRef (0.3V),
arm
- LPC系列处理器向量中断控制器VIC的功能原理-LPC series processor vector interrupt controller VIC function principle
nuc700-bootloader
- 新唐nuc700系列arm芯片的nor flash boot引导程序.-Once install on the target board, the NUC700 Boot Loader (WBL) is the first program to be executed after power on. It is responsible to initialize the system including memory interface, interrupt vector table, addr
different_PWM_for_three_phase_ACIM
- XE164单片机做的SPWM三相电机矢量控制。-XE164 microcontroller do SPWM three-phase motor vector control.
vecter
- 永磁同步电机的矢量控制，能够运行成功，可以作为一个很好的基层使用-Permanent magnet synchronous motor vector control, able to run successfully, you can use as a good grass-roots
stm32-foc-firwmare-libraries-v2.0
- 永磁同步电机矢量控制程序，位置与角度判断可通过霍尔位置传感器，编码器得到，其中也含有无位置传感器程序-Permanent magnet synchronous motor vector control program, to determine the position and angle through the Hall position sensors, encoders get, which also contains the program without position sensor
STM32_experiment-eight_INT
- 基于STM32的中断向量库开发，并且标注具体库函数名的位置以及相应设置方式，方便查找和理解。-STM32-based interrupt vector library development, and marked the location of a specific library function name and the corresponding set up, easy to find and understand.
NAND01GR3B_VH1
- 存储器verilog仿真代码，可以产生仿真向量对存储器测试。flash存储器选用march算法进行仿真测试。-Memory Verilog simulation code, you can generate simulation vector on the memory test. Flash memory selection of March algorithm simulation test.
Encoder_FOC_Motor_Example2
- 英飞凌xmc4500芯片永磁同步电机矢量控制程序，使用APP进行底层驱动配置。-a rotor field oriented vector control method by use of the xmc4500.
hrtf_paper3
- HRTF compression via principal components analysis and vector quantization