搜索资源列表
i2c总线
- iic总线资料，非常详细的iic总线资料-2005/09, 2005/09, very detailed information on bus
IIC
- 模拟IIC总线的C程序（软件延时产生SCL脉冲）-Simulation of C procedures IIC bus
IIC-8563-1602
- IIC总线控制8563时钟，并通过1602字符液晶显示万年历，51单片机控制实现-IIC bus control clock 8563, and through characters liquid crystal display 1602 calendar, 51 single-chip microcomputer to control the realization of
i2c
- iic总线编程的源代码介绍及源码调试好的程序-iic-bus programming source code for a good introduction and source debugging program
IIC
- S3C2440 ARM开发板下的IIC总线的试验程序-S3C2440 ARM development board under the IIC bus, the test procedure
IIC
- MSP430模拟iic总线，驱动ZLG7290程序-MSP430 analog iic bus, the driver ZLG7290 program
IIC
- 用标准Verilog HDL 语言编写的IIC总线IP核，详细定义了时序及输入输出， 可以直接应用-Standard Verilog HDL language of the IIC bus IP core, a detailed definition of the timing and the input and output, can be applied directly
8563T_AT917S64
- RTC PCF8563T AT91SAM7S64驱动 模拟IIC总线通信-RTC PCF8563T AT91SAM7S64 IIC
I2C
- iic总线驱动芯片的程序 51单片机测试通过-iic bus driver chip microcontroller program tested 51
iic
- iic的软件实现，模拟的iic总线，可以方便的读写eeprom-iic the software to simulate the iic bus, easy to read and write eeprom
IIC
- STM32单片机 IIC总线的控制C程序，通过I/O口来模拟IIC。-STM32 MCU IIC bus control C program, through the I/O port to simulate the IIC.
IIC
- 利用程序实现IIC总线读写数码管显示,并通过开发板验证-Program for IIC bus read and write using digital display
IIC
- 完整的51单片机IIC总线程序，KEIL的单片机程序，下载即可使用。-Complete 51 SCM IIC bus program, download it can be used.
iic总线源代码
- 此文件是iic总线驱动的源代码文件，iic.c 可以读写控制多个挂在总线上的器件。
iic总线oled屏幕驱动程序
- 四引脚（VCC/GND/SCL/SDA）iic总线oled屏幕驱动程序，51系列单片机可用（直接include即可）(Four pin (VCC/GND/SCL/SDA) IIC bus OLED screen driver, 51 series microcontroller can be used (direct include can))
IIC
- S3C2416 IIC总线协议与裸机实现代码(S3C2416 IIC bare metal code)
IIC总线
- AT89S51 单片机IIC例程 。(AT89S51 IIC Singlechip IIC routines)
stm32-IIC实验
- IIC总线协议实验，正点原子官方实验，包含部分OELD驱动(IIC bus protocol experiment,ALIENTEK official experiment)
iiC程序
- iiC总线由NXP（原PHILIPS）公司设计，多用于主控制器和从器件间的主从通信，在小数据量场合使用，传输距离短，任意时刻只能有一个主机等特性。此代码为基于单片机的程序。(The IIC bus is designed by NXP (formerly PHILIPS) and is mainly used for master-slave communication between the master controller and slave devices. It is used in
程序
- 通过IIC总线协议实现TM1637数码管模块0-100循环计数功能，并设置从0开始 每加数20次，蜂鸣器响1s钟。(The function of 0-100 cycle counting of TM1637 digital tube module is realized by IIC bus protocol, and the buzzer rings 1 s every 20 additions starting from 0.)