搜索资源列表
FIFO
- FIFO设计的难点在于怎样判断FIFO的空/满状态。为了保证数据正确的写入或读出，而不发生益处或读空的状态出现，必须保证FIFO在满的情况下，不能进行写操作。在空的状态下不能进行读操作。怎样判断FIFO的满/空就成了FIFO设计的核心问题。-FIFO design challenge is how to decide the FIFO empty/full. In order to ensure the correct data is written or read, or read the b
FPGA
- 结合FPGA和以太网传输的特点，设计了一套数据采集系统，应用FPGA的内部逻辑实现对ADC、SDRAM、网卡控制芯片DM9000的时序控制，以FPGA作为采集系统的核心，通过ADC，将采集到的数据存储到SDRAM中，以FIFO方式从SDRAM中读出数据，并将数据结果通过以太网接口传输到计算机-Combination of FPGA and Ethernet features, designed a data acquisition system, application FPGA' s i
uart16550
- uart16550 is a 16550 compatible (mostly) UART core. The bus interface is WISHBONE SoC bus Rev. B. Features all the standard options of the 16550 UART: FIFO based operation, interrupt requests and other. The datasheet can b
43680556EZ-USB_FX2_datasheet(Cy7C68013andCy7C68013
- ez-usb fx2 内含标准8051内核-ez-usb fx2 contains standard 8051 core
usb
- USBHostSlave is a USB 1.1 host and Device IP core. – Supports full speed (12Mbps) and low speed (1.5Mbps) operation. – USB Device has four endpoints, each with their own independent FIFO. – Supports the four types of USB data transfer control,
camera_up
- Camera Interface模块是视频输入转换存储模块。该模块一端接通用的video camera设备，另一端接AHB总线。实现了将Camera捕捉到的数据进行转换、并通过DMA存储到memory中。该IP支持ITU-R BT 601/656 8-bit 模式。支持YCbCr, RGB格式输入。可以将camera产生的YCbCr信号转换成24bit RGB 信号，然后下采样生成16bit RGB 5：6：5的LCD能直接读取显示的数据。该设备支持图像的镜像和翻转，以便适应手持式设备在移动环境
NIOS_JTAG_UART
- FPGA开发板上的JTAG——UART完成的工程设计，包括CPU内核设计合软件设计-FPGA development board JTAG- UART completed the engineering design, including the CPU core design combined software design
maxii_sch
- 采用EPM570作为核心，外接FIFO，RAM。可进行数据采集，采用60M时钟的ADC ADS830E。ADC前端电路需要改为差分输入方式以减小电路噪声。该电路经过实际检验可以使用，需要将JTAG电阻改为220以下或者短接。-EPM570 used as a core, external FIFO, RAM. Can be a data collection, using 60M clock ADC ADS830E. ADC front-end circuit differential inpu
fifo
- fifo使用手册，对于用IP core使用非常方便-fifo manual, for use with the IP core is very convenient
syn-fifo-verilog
- 用verilog语言写的同步FIFO设计源代码。-The source codes for syn-fifo using verilog language.
364652261
- FIFO一个用IP核调用的控制程序，里面有调用的IP核和FIFO读写控制-FIFO with an IP core call control procedures, which are called IP core and FIFO read and write control
fifoed_avalon_uart9.1_applicaton
- 用于Altera Avalon总线的、具有FIFO缓冲的Uart数据串口IP核以及应用于Nios2的、真正可运行的、容易移植的C代码。-Fifoed avalon uart IP core and C code for the IP core.
sdcard_mass_storage_controller_latest.tar
- 基于wishbone总线的SD Card IP Core,有Verilog和VHDL两种语言版本,包含了FIFO和DMA两种实现方式,是开源的IP Core-Based on the wishbone bus SD Card IP Core, there are two language versions of Verilog and VHDL, including the FIFO and DMA implemented in two ways, is open source IP Core
TERASIC_AUDIO
- 友晶提供的Audio的IP核。这个IP核提供了Verilog的硬件部分源码和相应的HAL驱动程序。-Audio provided by Friends of Crystal' s IP core. The IP core provides a Verilog hardware part of the source and the corresponding HAL driver.
RamFifoVHDL
- Ram Fifo Core VHDL file
fifouart_latest.tar
- vhdl fifo uart core datasheet
FT2232H_USB_Core
- 在FPGA外扩用FT2232 实现UART TO USB 2.0 的通信。-The FT2232H is a USB2.0 Hi-Speed USB Device to FIFO IC. This core allows the use of this chip with an FGPA design in high speed FT245 style synchronous FIFO mode. Data rates up to 25 mbytes/s can be achieve
mypro_synfifo
- 基于IP核RAM的同步fifo设计，工程使用Xilinx的开发软件ISE-RAM-based synchronization fifo IP core design, engineering, software development using Xilinx ISE
FIFOED_UART
- CAL_UART核verilog源码，带FIFO，FIFO深度可设置。-fifoed uart ip core. cal_uart.
异步FIFO
- 纯Verilog实现的异步FIFO，分为读写控制模块，SRAM CORE，同步等几个模块，内含源文件和仿真文件(The asynchronous FIFO implemented by Verilog is divided into read-write control module, SRAM core module and synchronization module)