搜索资源列表
51单片机控制CH375
- MCS-51单片机的C语言U盘文件读写示例程序，适用于89C52或者更大空间的单片机，也适用于ATMEL/PHILIPS/SST等具有1KB内部RAM的单片机(MCS-51 microcontroller C language, U disk file reading and writing sample procedures, applicable to 89C52 or larger space microcontroller, also applies to ATMEL/PHILIPS/S
Bank_simulation
- (银行)服务-客户交互的蒙特卡洛模拟 消息驱动机制 配置柜台数和客户特征，输出平均队列长度和平均等待时间。(Bank serve-client Monte Carlo simulation)
StepperMotor
- 89C52是INTEL公司MCS-51系列单片机中基本的产品，它采用ATMEL公司CMOS工艺技术制造的高性能8位单片机，属于标准的MCS-51的HCMOS产品。它结合了CMOS的高速和高密度技术及CMOS的低功耗特征，它基于标准的MCS-51单片机体系结构和指令系统 可控制总行程 可控制速度 可设定往返(Can control the total travel speed can be set and control)
65-18b20温控风扇
- 本系统就是充分利用了8051芯片的I/O引脚。系统以采用MCS-51系列单片机89c51为中心器件来设计简易温控风扇系统，实现了能根据设置的上下限温度，来启动风扇的工作与停止，低于设置的下限温度，风扇不工作，在上限与下限之间风扇以50%的转速工作，温度高于上限，风扇全速工作。(This system is to make full use of the I/O pin of the 8051 chip. The system uses MCS-51 series microcontroller
dingshiqi
- 采用定时器/计数器T0对外部脉冲进行计数，每计数100个脉冲后，T0转为定时工作方式。定时1ms后，又转为计数方式，如此循环不止。假定MCS-51单片机的晶体振荡器的频率为6MHz，请使用方式1实现(A timer / counter T0 is used to count the external pulse. After counting 100 pulses, T0 turns to a timing operation. After timing 1ms, it turns to cou
MCS_MATLAB_v3_1
- "Modified cuckoo search: A %new gradient free optimisation algorithm" Chaos, Solitons & Fractals Vol
MultimodalCuckooSearch
- A Cuckoo Search algorithm for multimodal optimization % An multi-modal optimization algorithm based on a evolutionary approach
MTL计算std和u
- 用MCS方法计算MTL的std和均值，给出图像，且统一了单位，很好的模拟了结果(The MCS method is used to calculate the STD and the mean of MTL. The image is given and the unit is unified. The results are well simulated.)
8051
- The resource code of The 8051 microcontroller is member of MCS-51 family, originally designed in the 1980's by Intel. The 8051 has gained great popularity since its introduction and is estimated it is used in a large percentage of all embedded system
单片机实验
- 单片机原理及实验以及源程序 实验一 功能：使连接在 MCS-51 单片机 P1.0 引脚的 LED 闪烁。 实验二 设计并调试一个双字节无符号数乘法子程序 实验三：设计并调试一个将双字节无符号二进制数转换为压缩 BCD数的子程序。 实验四：利用外部中断输入引脚（中断方式）控制步进电机的转动。(The principle and experiment of single chip microcomputer and the source program Experiment 1 func
按键处理办法
- 新型的按键扫描程序，这种按键处理办法的便捷和高效，你可以移植到任何一种嵌入式处理器上面，因为C语言强大的可移植性，你可以在MCS-51，AVR，PIC，甚至是ARM平台上面测试这个程序性能。(The new button scanning program, which is convenient and efficient, can be ported to any of the embedded processors. Because of the portability of the C l
MCS
- 以一典型高边坡为例，利用蒙特卡洛方法，模拟一百万次，计算边坡失效概率以及绘图。(Monte carlo method is used to calculate the slope reliability)
基于51单片机的信号发生器
- 基于MCS-51单片机的信号发生器设计及其应用系统(Design and Application System of Signal Generator Based on MCS-51 Single Chip Microcomputer)