资源列表
nRF24L01
- 2.4G 无线低功耗发送芯片nrf2401+的发送程序-the program is use to the IC for nrf24l01+
monitor
- 基于嵌入式Linux的视频监控器的设计和制作。（包括原理、设计方案、软件流程）-Embedded Linux-based video monitor in the design and production. (Including the principles of design, software process)
TMS320C5402_PRE_LTP_CODEC
- GSM0610 RPE-LTP算法在DSP上的实现-GSM0610 RPE-LTP algorithm implementation on DSP
mjpg-streamer-Tiny6410
- MJPG Streamer with Tiny6410 board
Tiny6410-Stream-MJPEG--Linux
- Article how to MJPG streamer with Tiny6410
ADE7755
- 基于单片机和ADE7755的分时计费电表的相关程序-Based on SCM and ADE7755 points billing electric meter procedures
jianpanqudou
- 主要是VHDL语言编写的键盘去抖程序，很正确，很实用-Mainly VHDL language keyboard to shake procedure, it is correct, it is practical
51clock
- 基于51单片的可调时钟，可用键盘控制显示时分秒，利用定时器中断-Based on 51 single adjustable clock, the keyboard can control display minutes and seconds, use a timer interrupt
Clk50M_div_1HZ
- Clk50M_div_1HZ，调试已通过，采用计数器分频 此实验采用计数器，将板载的50MHz时钟源分频为1Hz，分频的结果以LED灯的形式显示。下载电路至FPGA后，会发现LED0会以1Hz的频率闪动。-Clk50M_div_1HZ, using counter this study, frequency counter, onboard 50MHz clock frequency of 1Hz, frequency results in the form of LED lights di
Encoder4_2
- Encoder4_2，带优先级的编码器 此实验完成但优先级的4-2编码，以拨动开关SW[3..0]作为输入源（开关上拨时输入为高电平），其中SW[3]的优先级高于SW[2]的优先级，SW[2]的优先级高于SW[1]的优先级，以此类推。编码的结果会以LED灯的形式显示。例如，当SW[2]上拨而SW[3]没有上拨时，LED[1..0]的显示结果将是“10”。-Encoder4_2, with a priority encoder to complete this experiment, but
SEG_static
- SEG_static ，7段数码管译码及静态显示 此实验主要实现7段数码管（共阴极）的译码。拨动开关SW[3..0]代表输入的16进制数，译码电路将此16进制数转译成数码管上的段码，并静态地显示出来。-SEG_static, 7 segment LED decoder and the main achievement of this experiment the static display 7 segment LED (common cathode) decoding. Toggle swit
Adder_2bit
- Adder_2bit ，带进位处理的2位加法器 此实验中，实现了2bit宽度的加法运算，并带进位处理。加数与被加数分别以SW[3..2]和SW[1..0]来表示，加法的结果用数码管静态地显示出来。-Adder_2bit, with carry handle 2-bit adder this experiment, the realization of the addition operation 2bit width, and bit into the handle. Addend and