资源列表
4seg7disp
- 用电子表计时模块制作的单片机4位数码管时钟显示，很准的哦。-Electronic timing module production microcontroller Table 4 digital clock display, it is quasi-oh.
UCOSII-arm
- UCOS-II标准版ARM移植代码,可用UCOS-II初学者使用。-UCOS-II Standard ARM port code, UCOS-II is available for beginners.
UCOSII-arm
- UCOS-II高效版ARM移植，运行效率高于标准版。-UCOS-II version of the ARM port efficiency, the efficiency is higher than the standard version.
youyuanlvbo
- 本压缩包包含了多种滤波，包括；反相输入二阶低通有源滤波器，反相输入一阶低通有源滤波器，四阶有源带通滤波器，同相输入二阶低通有源滤波器等多种。-This archive contains a variety of filtering, including inverting input second-order low-pass active filter, inverting input a first-order low-pass active filter, the fourth-orde
dfbhsdg
- 在Keil uVision3环境下编写程序 1602+18B20+DS1302电子时钟源程序-Keil uVision3 environment in programming 1602+18 B20+ DS1302 digital clock source
lihao
- 关于led点亮的简单程序以及生成的hex文件。-Led light on the simple procedures and hex file.
ARM_JTAG_Debugger
- 设计 ARM JTAG 在线调试器的论文-arm JTAG debug
PID-contrel1
- 通过调整PID的三个参数KP、TI、TD ，将系统的闭环特征根分布在 s 域的左半平面的某一特定域内，以保证系统具有足够的稳定裕度并满足给定的性能指标 -Ziegler-Nichols method for tuning PID controllers can be summarized as follows: Set the integral and derivative gains to zero and increase the proportional gain until the
PID-contrel2
- 通过调整PID的三个参数KP、TI、TD ，将系统的闭环特征根分布在 s 域的左半平面的某一特定域内，以保证系统具有足够的稳定裕度并满足给定的性能指标-Ziegler-Nichols method for tuning PID controllers can be summarized as follows: Set the integral and derivative gains to zero and increase the proportional gain until the sys
tiepianruku
- 这是我写的2008年广东电子设计大赛控制类题目铁片入库小车，使用的凌阳６１Ａ单片机。-This is what I wrote in 2008 in Guangdong Electronic Design Contest category subject of iron storage control car, 61A using Sunplus chip.
pinghengxiaoce
- 这是我写的２００７年全国电子设计大赛题目跷跷板小车的程序，使用的是凌阳６１Ａ单片机开发板，附带语音控制。-This is what I wrote in 2007 entitled the National Electronic Design Contest seesaw car program, using the Sunplus 61A microcontroller development board, with voice control.
PID-contrel3
- 有被控对象的数学模型足够精确时，才能把特征根精确地配置在期望的位置上，而大多数实际系统一般无法得到系统的精确模型，因此理论设计的极点配置往往与实际系统不能精确匹配 -Manual Mode Controller output, p(t), is adjusted manually. Manual Mode is very useful when unusual conditions exist: plant start-up p