资源列表
LIB
- REAL TIME CLOCK IC DRIVER IN MIKROBASIC COMPILER THAT USE STANDARD SOFTWARE I2C OF MIKROBASIC COMPILER FOR CONNECTION WITH DS1307 RTC IC
LPC1768_PWM(2014.05.10)
- lpc1768 的pwm源码程序，该例程使用的硬件为led，用pwm模块产生波形，使led不同亮度-lpc1768 of pwm source program, the routine use of hardware led, with pwm module to generate waveforms that led different brightness
1768_EEPROM(2014.05.10)
- lpc1768 i2c eeprom,可以进入debug模式验证我们写进去的数据和读出来的数据是否一致-lpc1768 i2c eeprom, can we enter debug mode to verify that data written into and read out the data consistency
zImageAndCodeAndTestCode
- 在0K6410的开发板上，s3c6410芯片上，添加SPL驱动，编译成功的内核镜像以及修改的代码部分和测试代码。-On 0K6410 development board, s3c6410 chip, add SPL driver, successfully compiled kernel image and modify part of the code and test code.
led_new
- 该程序是基于cortexA8 am3354自带的驱动程序而编写的led驱动测试程序-Sorry ， i cant speak english
UCOSII-1
- UCOSII的任务创建，在UCOSII里面创建3个任务：开始任务、LED0任务和LED1任务，开始任务用于创建其他（LED0和LED1）任务，之后挂起；LED0任务用于控制DS0的亮灭，DS0每秒钟亮80ms；LED1任务用于控制DS1的亮灭，DS1亮300ms，灭 300ms，依次循环。-UCOSII task created inside the uCOSII create three tasks: task and LED0 task and LED1 task start, start
1768_UART(2014.05.10)
- lpc1768 的串口源程序，设置好波特率115200，发送测试文件数据-lpc1768 serial source, set the baud rate 115200, send a test file data
UCOSII-2
- UCOSII的任务调度,led_task是LED0和LED1每隔500ms翻转一次,beep_task在没有收到删除请求的时候是隔一段时间蜂鸣器鸣叫一次，key_task是进行按键扫描。-UCOSII task scheduling, led_task is LED0 and LED1 every 500ms flip once, beep_task in the absence of a request to delete the request is separated by a perio
1768_RS-485(2015.09.6)
- lpc1768的485通信源程序，程序编译无误后，下载led亮表示程序正常运行-lpc1768 485 communication source, after the program compiles correctly, download led light indicates normal operation procedures
UCOSII-3
- UCOSII的消息队列、信号量集和软件定时器等资源的使用.-UCOSII message queue, the signal volume set and the use of the software timer and other resources.
UCOSII-4
- UCOSII的信号量和邮箱等资源的使用,蜂鸣器任务用于测试信号量，是请求信号量函数，每得到一个信号量，蜂鸣器就叫一次.-UCOSII signal and mailbox and other resources, the buzzer task for testing the amount of signal is a request signal function, each get a signal, the buzzer is called once.
LPC1768_ADC(2014.05.10)
- lpc1768,模数转换源程序，将模数转换数值显示在屏幕和通过串口发送出来-lpc1768, analog to digital conversion source, the analog to digital conversion value is displayed on the screen and sent out through the serial port