资源列表
tm4c123_mpu6050_test
- TIVA模块移植mpu6050程序测试成功，通过模拟I2C进行连接-TIVA mpu6050 module transplantation program was successful, by simulating I2C connection
chaoshengceju
- 51单片机的超声波测距程序，在51单片机上调通，能准备测出距离，误差在3cm以内-51 microcontroller Ultrasonic Ranging procedure in regulation 51 single-pass, can prepare measured distance error less than 3cm
lovelight
- 心形灯程序，有15种模式的自由切换，可以在程序里面增加删除-Heart lamp program, have the freedom of 15 kinds of mode switch, can add delete inside the program
yaoyaobang
- 大一时做的摇摇棒程序，16个发光二极管，在摇动过程中由于视觉暂留效应，能通过编程显示不同的字符或者简单的图像-At the do rocking bar program, 16 leds, due to persistence of vision effect, in the process of shaking can programmed to display different characters or simple images
yejing12864tiaohao
- 大屏液晶12864在51单片机上测试成功，最重要的是能够在protues上实现下载程序仿真，显示相应的在线操作-Screen LCD 12864 on 51 single chip microcomputer test is successful, the most important to be able to download a program implementation on protues simulation, according to the corresponding onli
spi_verilog
- spi通信协议的设计参考，对于初学者可以以此为参考进行设计，代码可在仿真软件中验证（modelsim、VCS等）。-Spi communication protocol design reference for beginners can be used as a reference design, the code can be verified in the simulation software (modelsim, VCS, etc.).
Control-Led-light-off
- GPIO输出控制实验-控制led亮灭，cc2530芯片的配制方法-GPIO output control experiment- control LED light out, CC2530 chip preparation method
uart_model_verilog
- uart通信协议的设计参考，对于初学者可以以此为参考进行设计，代码可在仿真软件中验证（modelsim、VCS等）。-Uart communication protocol design reference for beginners can be used as a reference design, the code can be verified in the simulation software (modelsim, VCS, etc.).
dma_bridge_verilog
- DMA控制模块的设计参考，对于初学者可以以此为参考进行设计，代码可在仿真软件中验证（modelsim、VCS等）。-DMA control module design reference, for beginners can be used as a reference design, the code can be verified in the simulation software (modelsim, VCS, etc.).
3-button-control-LED-light-off
- 掌握按键的使用，实现人机交互，按键控制LED亮灭。-Master the use of buttons to achieve human-computer interaction. Button control LED light off
usb_host_device_verilog
- USB-host-device控制模块的设计参考，对于初学者可以以此为参考进行设计，代码可在仿真软件中验证（modelsim、VCS等）。-USB-host-device control module design reference for beginners can be used as a reference design, the code can be verified in the simulation software (modelsim, VCS, etc.).
buttons-control-the-LED-Marquee
- 按键控制LED跑马灯,读取按键状态,设置 LED 灯相应的 IO 口,设置按键 S1 相应的 IO 口, 扫描按键当前状态,按下时执行跑马灯效果.-The control button LED marquee, read the key state, set the corresponding LED lamp IO port, IO port settings button S1, Key scan the current state of implementation of the