资源列表
dds
- 如何利用FPGA产生DDS调频信号 很具体的-How to make use of DDS generated FM signal FPGA specific
wentuji
- 运用vb编写上位机，显示下位机中温度数值以及波形，下位机程序用c编写.-Vb prepared to use PC to show lower values, as well as machine temperature waveform, the next c-bit machine with the preparation procedure.
SPI_7SegLed
- LPC2131 SPI通信 proteus里面仿真实现-LPC2131 SPI communication inside the simulation proteus
UART
- LPC2131 串口通信 原程序 proteus里面已实现-LPC2131 original serial communication program
GPIO-deng
- LPC2131 实现流水灯实验，proteus里面实现-LPC2131 experimental realization of light water, proteus which to achieve
CS18-2
- 定时中断。采用定时器T0，定时50ms，每次定时溢出引起中断，在中断程序中对计数器累加。每一秒LED亮0.2s，熄0.8s。 特色：低功耗。程序中技巧在于将1s分成cnt记20次，0.2秒占20 ，即中断的前4次都点亮，后16次都熄灭。-Interrupted from time to time. The use of timer T0, from time to time 50ms, each caused by overflow from time to time interrupted
DE2_SD_Card_Audio(Modified)
- 在DE2开发板上实现的SD卡mp3音乐播放器。硬件部分用Verilog语言编写，在Quartus上编译；软件部分用C语言编写，在Nios2上编译运行。-DE2 development board in the realization of the SD card mp3 music player. Hardware using Verilog language, compiled in the Quartus software with C language, compiled to run
LED_FAN
- 程序工作流程是： 1、产品按下电源开关，给电机及电刷供电，电机开始转 动，单片机得电也开始工作； 2、循环等待24圈，让电机转速基本稳定； 3、一圈计时，然后根据需要显示的总点数计算出每点的 延时； 4、检测同步信号； 5、取显示数据输出到端口上、延时，重复显示完所有的 数据； 6、一直重复第4、5步。-Workflow process are: 1, product press the power switch, power supply to the mo
LabVIEWToMultiCpu
- labview与多个单片机通信程序，希望对大家有用-labview communication program with a number of single-chip, in the hope that useful
bldc_code
- 四轴飞行器的无刷电机驱动的源代码，适用于atmeg8芯片的板子-Four aircraft brushless motor-driven source code, apply to the board atmeg8 chip
DE1_i2sound
- Altera的DE1平台资料，实现de1的音乐播放功能-Altera' s DE1 platform for information, the realization of the music player function de1
UCOS2-FOR-AVR
- 摘 要: 在单片机中移植嵌入式操作系统是嵌入式系统发展的一个热点,也是未来发展的方向. 介绍嵌入式操作系统在单片机应用的优势和μC/ OS2 Ⅱ的特点,并结合AVR 单片机的应用实例,分 析μC/ OS2 Ⅱ的移植过程和基本方法. 采用μC/ OS2 Ⅱ可以大大简化程序设计,满足实时要求,降低 开发难度,提高系统可靠性.-Abstract: The transplantation of single-chip embedded system Embedded operating s