资源列表
FM24C256_Read_And_Write
- 铁电存储器FM24C256读写操作,只要调用现成的函数就可以了,这些函数也可以用来操作IIC总线有关的设备.实际使用时根据单片机速度和晶振适当改一下延时-FM24C256 ferroelectric memory read and write operations, as long as the existing function calls can be, these functions can also be used to operate IIC bus-related equipment
Interrupt_cc2430_cc1110
- 提供两个基于IAR开发的中断系统的使用方法，分别为定时器和外部中断。适当修改例程同样适用于CC1110/CC2510 和外部中断-Two IAR-based system developed by the use of interruptions, namely timer and external interrupt. Routines with appropriate modifications apply equally to CC1110/CC2510 and external inte
HT46F49E-SEND
- 用台湾的合泰单片机驱动SI4421射频模块的发送程序，绝对正确，已测-Taiwan' s cooperation with the Thai Microprocessor SI4421 RF module sending program, absolutely right, has been measured. . . . . . . . . . . . . . . .
SVPWM
- 空间适量调制的仿真，因为控制矢量比较难理解，通过此模型的仿真，便于我们对它的理解。-Space vector modulation simulation, because the control vector is more difficult to understand, through the simulation of this model, to facilitate its understanding
TLC5620
- 该源码为DA芯片TLC5620的完美驱动，程序中附带产生三角波、方波的功能，工程环境为Keil C51
read_amdv10
- 读取AM29F040B数据！本程序可以通过串口调试工具发送一个六位十六进制的地址数读取出AM29F040B相应地址上的数据 经测试数据正确有效-The program can send through the serial port debugging tool addresses a number of six hexadecimal AM29F040B read out the data on the corresponding address data is correct and
电磁炉控制
- 压缩文件包括电磁炉的控制程序和其原理电路图！方便大家阅读程序，配合原理图阅读！-compressed files including Induction Cooker control procedures and its tenets circuit! To facilitate reading the procedure to incorporate the diagram read!
C51+remote
- 单片机与遥控器的通信、红外编码及接收信号处理
CC2530-13
- CC2530-13 单片机串口发数，已通过实验验证，完全可用。-CC2530-13 microcontroller serial port to the number has been verified by experiments, completely free.
S3C2440Bootloader
- 结合嵌入式Linux系统的引导程序，重点分析了基于ARM处理器的嵌入式Bootloader总体框架，设计出了基于“NAND Flash +SDRAM”存储方式的Bootloader，并对SDRAM的地址进行测试，结果表明此Bootloader灵活高效。-Embedded Linux system with the boot process, focusing on analysis of embedded processors based on ARM Bootloader general fr
Infrared-negative-solution
- 使用外部中断0连接遥控头，接收红外遥控键值送P1口显示，12MHz外部晶振-The use of external interrupt 0 is connected with the remote infrared receiving head, infrared remote control key delivery port P1 display, an external crystal oscillator 12MHz remote control decoding procedure
ex05_keyscan
- 单片机键盘扫描程序，请朋友们试试，如果需要更多程序，请合我联系-SCM keyboard scanning procedures, please friends try, if need more procedures, please contact me Hopewell