资源列表
jidianqi
- 51单片机例程，继电器控制实验，配有实验说明文档。-51 MCU routine, relay control experiment, with experimental documentation.
jianpankongzhideng
- 51单片机例程，键盘控制灯，配有实验说明文档。-51 MCU routine, keyboard light, with test documentation.
c51
- 主要是单片机开发板的原理图和应用实例程序-Mainly MCU development board schematic and examples of program application
baojingqi
- 用P1.0输出1KHz和500Hz的音频信号驱动扬声器，作报警信号，要求1KHz信号响100ms，500Hz信号响200ms,交替进行，P1.7接一开关进行控制，当开关合上响报警信号，当开关断开告警信号停止，编出程序。-1KHz and 500Hz with the P1.0 output audio signals to drive speakers, as alarm signals to require 1KHz signal ring 100ms, 500Hz signal ring 2
guanggaodeng
- 利用取表的方法，使端口P1做单一灯的变化：左移2次，右移2次，闪烁2次（延时的时间0.2秒）。 -Take advantage of the method table, so that a single lamp to do the port P1 changes: left 2 times, shifted to the right 2 times, flashing 2 times (delay time of 0.2 seconds).
shanshuodeng
- 如图4.1.1所示：在P1.0端口上接一个发光二极管L1，使L1在不停地一亮一灭，一亮一灭的时间间隔为0.2秒。 -As shown in Figure 4.1.1: the P1.0 port by one light-emitting diode L1, L1 to keep a light in one off, a light one off the time interval of 0.2 seconds.
monikaiguandeng
- 如图4.2.1所示，监视开关K1（接在P3.0端口上），用发光二极管L1（接在单片机P1.0端口上）显示开关状态，如果开关合上，L1亮，开关打开，L1熄灭。-As shown in Figure 4.2.1, monitor switch K1 (connected to the P3.0 port), with a light-emitting diode L1 (P1.0 port connected to the MCU) shows off state, if the switch is
duolukaiguandeng
- 如图4.3.1所示，AT89S51单片机的P1.0－P1.3接四个发光二极管L1－L4，P1.4－P1.7接了四个开关K1－K4，编程将开关的状态反映到发光二极管上。（开关闭合，对应的灯亮，开关断开，对应的灯灭）。 -As shown in Figure 4.3.1, AT89S51 MCU P1.0-P1.3 take four light emitting diodes L1-L4, P1.4-P1.7 received four switches K1-K4, programming re
IOqudongled
- 如图13所示，利用AT89S51单片机的P0端口的P0.0－P0.7连接到一个共阴数码管的a－h的笔段上，数码管的公共端接地。在数码管上循环显示0－9数字，时间间隔0.2秒。 -Shown in Figure 13, using AT89S51 microcontroller ports P0.0-P0.7 P0 is connected to a common cathode tube in a-h digital pen section, the digital control of pub
51wenkongxitong
- 基于51单片机的智能温控系统-Based on 51 of Intelligent Temperature Control System
avr_ad
- 基于M16的A/D代码，调试通过，是不错的AVR参考代码-very good!!!!
m16_1602
- 基于AVR m16的1602液晶显示器程序代码，调试通过，非常不错。-good！！！！！！