资源列表
transmit
- 用PIC12C508单片机做发射及接收，只要加上RF发射及接收模块即可当作遥控器使用,这是发送程序-do with PIC12C508 SCM launch and reception plus RF transmitter and receiver modules can be used as a remote control device, which is sent procedures
CDANPIANJI
- 单片机无时钟控制源码.用C语言编写的，比汇编语言通俗易懂，还有文字说明-SCM no clock source control. C language, more so than assembly language easily understood, there is a textual descr iption
LCD
- This module provides an interface to an alphanumeric display module. The current version of this driver supports any alphanumeric LCD module based on the:Hitachi HD44780 DOT MATRIX LCD controller.
AD-LCD-LED-KEYBD
- 单片机各种功能开发的.asm格式源码，包括：AD转换；走马灯的实现（包括4种灯亮灭的情况）；键盘中断响应及键盘输入值的输出；LCD模块显示数值方法的实现源码-SCM developed various functions. Asm source code format, including: AD conversion a revolving door of implementation (including 4 light off the case) keyboard and keyboa
wannianli
- 经过伟福编译通过的万年历源汇编语言代码。时分秒，年月日，星期都可显示-Compiled by DW calendar source assembly language code. , Hour, month, day, week can be displayed
IIC
- 两个M16通过TWI进行通信,主机与从机程序-Two M16 communicate through TWI, the host and slave program
PCAfangbo
- PCA可调频率方波输出，8位调频,利用PCA频率改变方波频率-PCA adjustable frequency square wave output, 8 FM, using the change in frequency square-wave frequency PCA
dianyabiao
- 基于AT89C51的简易数字电压表的设计，在PROTUES环境下仿真-AT89C51 Based on a simple digital voltage meter design, the PROTUES simulation environment
vcmk1b
- pic单片机电压斜率测量工频电压，通过测量某点固定电压值的脉冲宽度计算对应的电压值-pic microcontroller voltage slope measured frequency voltage, a point fixed by measuring the voltage pulse width corresponding to the voltage calculation
LCD时钟C51
- //日历时钟 //按AN1,进入设置状态 //按AN2,停止闹钟声音 //按AN3,依次进入闹钟功能是否启用，闹钟时,分秒,年,月,日及时间时,分,秒的设置,直到退出设置状态 //按AN4,调整是否起用闹钟和调节闹钟时,分,秒,年,月,日,时间的时,分,秒的数字 //LCD第二排中间显示小喇叭，表示启用闹钟功能，无则禁止闹钟功能（可在调整状态进行设置） //正常状态,LCD上排最前面显示自定义字符,LCD下排最前面闪动\"willar\" //设置状态,LCD上排最前
hwdriver
- 手写IC（EPH1100）的80C51驱动软件。-handwritten IC (EPH1100) 80C51-driven software.
09-02_fangzhen
- Every time a byte becomes available from the serial port, then "RxD_data_ready" is active for one clock period. The PC sends us data through the serial port in 8-bits mode. Ideally, we would need to receive 9 bits from the PC, so that we can drive