资源列表
reconfiguration
- 本程序用于配电网的网络重构，能有效、快速的对配电网做出重构，方便实用。(This program is used for the network reconstruction of the distribution network, which can effectively and quickly reconstruct the distribution network, which is convenient and practical.)
粒子群算法综合线阵低副瓣方向图
- 利用粒子群算法综合微带天线阵列方向图，可以自适应调节副瓣电平和波瓣宽度。(By using particle swarm optimization (PSO) to synthesize the pattern of microstrip antenna array, the sidelobe level and lobe width can be adjusted adaptively.)
汽车悬挂设计matlab
- 1.被动悬挂设计simulink模型 2.对于任意一段路面谱，求出其功率谱密度与频率的分布关系，在标准路面图中画出曲线验证路面 3.积分白噪声法路面构造simulink模型 4.整车平顺性分析simulink模型 5.实际路谱案例，c级路面 6.悬架动载荷功率谱密度图像画图matlab编程(1. Simulink model for passive suspension design 2. For any section of road spectrum, the
14自由度汽车模型以及论文
- 汽车14自由度仿真simulink文件，包括车身6个自由度，悬架4自由度，车轮4自由度。模型跑得通，且和carsim中同种工况下的运行结果相同，精度较高。 除此之外还有模型搭建的对应论文可供参考学习(Vehicle 14 DOF simulation Simulink file, including 6 DOF of body, 4 DOF of suspension and 4 DOF of wheel. The model runs well and has the same result
计科软件对161_陈金金_水果识别
- 基于matlab的水果识别系统，含报告，源码(Fruit recognition system based on matlab, including report, source code)
Chirp信号的匹配滤波
- 利用matlab仿真产生线性调频信号，并实现线性调频信号的匹配滤波。(Using matlab simulation to generate LFM signal and realize matched filtering of LFM signal.)
趋势EA
- 趋势EA，不加仓，不网格，每单都带止损止盈，加载周期30分(Trend EA, no warehousing, no grid, stop-loss and stop-profit for each single, loading cycle 30)
天线波束方向图
- 考虑一长度为D，宽度为L的理想均匀面阵天线，并用Matlab画出其二维波束方向图。(Consider an ideal uniform planar array antenna with length D and width L, and draw its two-dimensional beam pattern with MATLAB.)
非线性动力学-分岔图-混沌-程序
- 上海交通大学非线性动力系统的分岔图绘制实例，非常简单好用。(The example of drawing bifurcation diagram of non-linear dynamic system in Shanghai Jiaotong University is very simple and easy to use.)
parameters_2_story(1)
- 此代码是2个自由度的bouc-wen模型代码，如有漏洞，敬请指出(This code is a Bouc-Wen model code with 2 degrees of freedom. If there is a loophole, please point out)
boucwen_2story_
- 此boucwen滞回模型建立在matlab-simulink仿真基础上(The boucwen hysteresis model is based on matlab-simulink simulation)
example
- 此模型是基于MATLAB-simulink，用boucwen滞回模型分析单自由度体系的振动反应(This model is based on MATLAB-simulink. The boucwen hysteresis model is used to analyze the vibration response of a single-degree-of-freedom system.)