搜索资源列表
Gaositouyingzhengfansuan
- 大地测量学中的高斯投影正反算过程。用C#实现,界面友好。-Gaussian projection geodesy pros and cons of the counting procedure. C# friendly interface.
12864
- The C project about msp430g2553,describes the msp430g2553 and 12864, including the use of various registers and gives a programs, counting experiments.
maplusi
- 设计一个秒表,该跑表使用一个按钮k工作,当第1次按下按钮时,秒表开始计数,第2次按下按钮时,秒表停止计数,第3次按下按钮时,秒表计数器继续计数,第4次按下按钮时,秒表计数器停止计数,如此反复。若是在停止计数状态,按钮的按下时间超出2s,则秒表计数器清零-Design a stopwatch, the stopwatch with a button k work, when the 1st button is pressed, the stopwatch starts counting, pres
CardGames
- 扑克牌比较大小的游戏,主要是根据花色、点数的不同来比较牌的大小。-Comparing the size of the poker game, mainly based on colors, counting to compare different size cards.
pulse_count
- 用51单片机的中断另一个功能gate门做实现脉冲计数-Microcontroller with a 51 break to do other functions to achieve pulse counting gate door
Electric_clock_design_with_VHDL
- 本次设计的电子钟具有正常计时,时间手动设置,闹钟,秒表四种功能,能够输出24小时制的时间。 电子钟上电reset后,即以默认设置的时间00:00:00开始正常计时,工作模式为计时模式。mode键是工作模式切换键,按照计时—设置—闹钟—秒表四种模式一次切换。在正常计时模式下,按一下mode键切换至设置模式,left和right键用来调整小时或分钟使能被设置,up和down键用来调整时间,调整单位是1;设置好时间后按start_stop键确认(此处使用start_stop键作为ok键使用)。闹钟
lesson14
- 数码管自动计数,有归零暂停,继续等功能,用单片机控制数码管实现,用C语言编写-Digital automatic counting, there are zero pause, resume, and other functions, with a single chip digital control implementation, using C language
exp15
- 本实验的任务就是设计一个秒表,由于计时时钟信号为50MHz,因此需要对系统时钟进行500000分频才能得到。另外为了控制方便,需要一个复位按键、启动计时按键和停止计时按键,分别选用实验箱按键模块的KEY0、KEY1和 KEY2,按下KEY0,系统复位,所有寄存器全部清零;按下KEY2,秒表启动计时;按下KEY1,秒表停止计时,并且七段码管显示当前计时时间,如果再次按下KEY2,秒表继续计时,除非按下KEY0,系统才能复位,显示全部为0000--00。-The task of this exper
keyled1
- elan单片机编程 2个八位数码管计数,按键一次,从0-99递增-SCM Elan programming2 of eight digital tube counting, button once, from 0-99 increments
cigarette-no
- 根据生产线的图片识别香烟的数目!并且能克服光照的影响!-counting the cigarette no. of the factory!
Td022rarh
- 此程序源码为脉宽测量电路vhdl代码,能够对输入的脉冲信号用10HZ时钟进行计数数,输出计数结果。主模块调用显示出来、计数、控制三个模块实现主体功能 可直接使用。 -This program source for a pulse width measuring circuit VHDL code, it is possible to input a pulse signal with 10HZ clock count number, the output of the counting re
CImageProojo
- 对图像进行灰度图转化,锐化等功能能,和图像识别与计数功能可直接使用。 -The function can be transformed grayscale image sharpening, and image recognition and counting function can be used directly.
jishu
- 雨流计数法,好东西,计算疲劳强度的同学 可以下载完成后试用一下。-Rainflow counting method, good things, calculate the fatigue strength of the students can download the complete trial.
Josephus
- 约瑟夫环的问题 用链表来实现的 可以输入人数 退出的号和从第几个人开始计数-Josephus linked list, you can enter the number of exit number and start counting from the first few people
Ttmultiii
- 对一维时间序列采用盒计数法对其其进行多重分形谱的计算可直接使用。 -Its multifractal spectrum calculation can be used directly on the time series of one-dimensional box counting method.
di1
- 计数器的设计,可以累加计数。实现计数功能,代码功能如下所示。-Count-counter design. Counting function, the function of the code is shown below.
main
- 利用dsp2812实现自动计数功能,利用事件管理器EV实现-Dsp2812 automatic counting function, Event Manager EV achieve.
Counts
- This Function Is Example Java Code For Counting-This Function Is Example Java Code
Fractal-Dimensions
- 利用MATLAB的图像处理和数值计算功能得到颗粒物边界的二值图像;编制MATLAB程序,统计一系列以不同像素数量为边长的正方形块覆盖二值图像时的个数,根据像素数量和正方形块个数之间的关系,确定图像的计盒维数。-Image processing and numerical calculation using MATLAB function obtain pellets boundary of the binary image preparation of the MATLAB program,
design_4
- 利用48M时钟信号定时得到事先设置好的延时,通过延时信号接到蜂鸣器发出提示声音。主持人,抢中,抢答时间到,答题时间到,四个信号分别触发计数延时,最后把得到的三个报警信号相与(因为系统设置为低电平有效),作为最后的报警信号。 每个触发延时计时,在触发信号无效(‘1’)时,将计数值归零,触发信号有效时(‘0’),开始记时钟个数,记到一定(根据需要事先设置好)个数,就得到延时时间(延时时间=时钟个数*时钟周期),时间延时报警信号无效,得到一定时间的报警信号。 -48M clock signal t