搜索资源列表
实验2:LED闪烁
- 51开发板中第2个程序点亮所有led,运行程序后会自动点亮所有小灯(The second program in the development board lights up all the leds, and the running program automatically lights up all the small lights)
实验3:LED流水灯
- 51开发板中第3个程序循环流水灯,运行程序后会自动点亮所有小灯并闪烁(The 3rd program in the development board is circulating the running water lamp, which will automatically light all the small lights and blink when the program is running)
LED
- STM32控制流水灯实验程序,控制程序流水灯(STM32 control flow lamp experiment program, control program flow lamp)
LED KEY
- LPC5411XLED流水灯, 实现轮询闪烁。可以控制闪烁时间,key健。所有LPC82x器件的存储器映射都相同。不同的LPC82x器件支持不同的闪存和SRAM存储器大小。(GPIO registers support up to 32 pins on each port. Depending on the device and package type, a subset of those pins may be available, and the unused bits in GPIO r
【01】红牛板_LED(2016.05.04)
- 基于红牛开发板led灯实验详解 里面有代码实现方法(Based on the Red Bull development board LED lamp experiment detailed solution inside code implementation method)
led.gz
- 基于S3C2440的灯光控制驱动开发,实现远程控制终端设备小灯,模拟智能家居远程监控系统,实现远程控制小灯。(Based on S3C2440's lighting control drive development, realize remote control terminal equipment small lamp, simulate intelligent home remote monitoring system, realize remote control small light
然并卵的灯
- 功能 1、单键开关LED 2、在LED开启状态下旋转编码器可以调节pwm以控制LED亮度 3、在LED开启状态下双击达到最大亮度(实际就是程序事先设定好的) 4、在LED开启状态下长按进入延时关断,延时65s,最后10s指示灯闪烁 5、在延时关断状态下单击取消延时关断 6、关断或者掉电后会记忆最后亮度(掉电记忆) 注: 1、短按操作:按键按下,按下时间<1s,属于一次短按操作 2、长按操作:按键按下,按下时间>1s,属于一次长按操作(The function of
Lab1_EE319K_C
- 嵌入式系统下的单片机开发,控制LED灯,以及端口设置(Development of single chip microcomputer)
1KeyControl2Laser-12f508
- 通过一个按键来控制两个LED灯的亮灭状态的转换。(one Key control two LED)
led
- 数据采集实验中的一个作业,简单的流水灯循环及其实现,基于LabWindows CVI平台,可实现颜色调整和时间间隔选择。(A job in data acquisition experiment, a simple water lamp cycle and its implementation. Based on LabWindows CVI platform, color adjustment and time interval selection can be realized.)
STM8S103F3GPIO输出_流水灯控制___Lib
- STM8S103F3GPIO输出_流水灯控制LED(The output of the STM8S103F3GPIO _ light water control ___Lib)
STM32-LED闪烁-消息队列
- STM32LED闪烁——消息队列,通过建立消息队列,传送3个指针型变量,触发LED灯闪烁。(By setting up a message queue, 3 pointer variables are transmitted, triggering the LED light to flicker.)
STM32 led测试程序
- 这是一个基于STM32F103C8T6 的LED流水灯程序。可测试所有端口(This is a STM32F103C8T6 based LED pipelining light program. All ports can be tested)
STM32 led测试流水灯程序
- 这是一个基于STM32F103C8T6 的LED流水灯程序。大家可以试用 一下。(This is a STM32F103C8T6 based LED pipelining light program. You can try it out.)
led
- LED灯显示,利用VHDL语言实现数码管中的灯的显示功能(The LED lamp shows that the display function of the lamp in the digital tube is realized by the VHDL language)
AnalogInput_B用旋转改变小灯闪烁频率
- Arduino编程,使用旋转点位模块传感器控制LED灯的闪烁频率(Arduino programming, using a rotating point module sensor to control the flicker frequency of the LED lamp)
STM32_20170814_LED
- 用STM32实现LED灯闪烁,适合于初学者使用借鉴。(LED light flicker with STM32)
GenericLEDApp
- zigbee,一个节点通过控制开关,可以控制另外一个节点开发板上led的亮灭。(ZigBee, a node can control the brightness of the LED on another node development board through a control switch.)
Proteus平台8086的交通灯汇编语言实现
- 基于proteus平台,采用8086处理器,利用汇编语言编写,可作为微机原理课程设计。设计一套十字路口的交通灯管理系统,通行时间(或禁止时间)30秒,准备时间3秒,在准备时间里黄灯闪烁3次,闪烁频率为0.5秒,周而复始。若有紧急情况(救护车通过),申请中断,四个方向全部红灯,10秒后重新开始。(进一步设计,可以利用实验箱上的多位数码管显示两个方向的倒计时,或LED点阵显示停、行汉字或动画)(Based on the Proteus platform, using 8086 processors
02 从左到右的流水灯
- 单片机控制LED从右至左亮,不断地依次循环(Single chip microcomputer control LED from right to left)