搜索资源列表
CC2500-DONGLE-RX-V40
- 这个是CC2500在em78p447的程序-the CC2500 is in the process em78p447
9E5-Rx
- 无线单片机nFR9E5的收发程序例子,供参考 -wireless transceiver examples of procedures for reference
smsc911x_xscale_v1.12
- smsc911x 网卡驱动 This the users/programmers guide for the LAN911x Linux Driver The following sections can be found below * Revision History * Files * Features * Driver Parameters * Rx Performance Tuning * Tested Platforms * Rx
Rx
- CC1100做呼叫器的程序(C语言)用8051与CC1100接口,语音压缩,频率在916.5MHZ
Infrared-RX
- 用单片机接收红外线IC发出的信号，汇编语言格式。
test05
- UART RX with simple logic flow to check the protocol correct or not. Important is that the logic flow.
905
- NRF905驱动代码 // The content of this struct is nRF905 s initialize data. // CH_NO=1 433MHZ Normal Opration,No Retrans RX,TX Address is 4 Bytes // RX TX Payload Width is 32 Bytes Disable Extern Clock Fosc=16MHZ // 8 Bits CRC And enable
io
- ecos serial rx and tx
msp430x11x1_ta_uart9600_04
- Descr iption: This program demonstrates a half-duplex 9600-baud UART using // Timer_A3 using no XTAL and an external resistor for DCO ROSC. DCO used for // TACLK UART baud generation. The program will wait in LPM4, echoing back // a received ch
tX+RX+Xmodem
- 标准的c代码，支持Xmodem的接受和发送，支持短线重传，而且随时都可以用ESC断开。功能强大。在4510上可以直接使用。
rx
- 这个程序是控制无线模块2401接受，为51系列单片机控制。可以将接收到的字节上传到电脑的串口
fet440_uart11_38400
- Echo a received character, RX ISR used. Normal mode is LPM0. // USART1 RX interrupt triggers TX Echo. // Baud rate divider with 1048576hz = 1048576/38400 = ~27.31 (01Bh|03h) // ACLK = LFXT1 = 32768Hz, MCLK = SMCLK = default DCO = 32 x ACLK = 10
rx
- 家电自动控制系统，定时开关，采用遥控器，按键操作，中文12864液晶示，-appliance control system, timing switches, using remote controls, buttons, LCD showed 12,864 Chinese,
f347 uart
- f347 uart tx/rx
trunk-hdlc.rar
- 高级链路层协议的实现，vhdl，fpga,- 8 bit parallel backend interface - use external RX and TX clocks - Start and end of frame pattern generation - Start and end of frame pattern checking - Idle pattern generation and detection (all ones) - Idle pattern
RX
- 1路视频光端机的接收端，VHDL源码，使用全FPGA芯片的硬件，内建解帧、时钟、DESERDES-PDH a video of the receiving end, VHDL source code, use the whole FPGA chip hardware, built-in framing, clock, SERDES
usb_phy.tar
- Very simple USB 1.1 PHY. Includes all the goodies: serial/parallel conversion, bit stuffing/unstuffing, NRZI encoding decoding. Uses a simplified UTMI interface. Currently doesn t do any error checking in the RX section [should probably check f
CC1100_RF
- 这个是CC1100的通信程序，包含了所有的功能，WOR,CCA,RX TX等-This is the CC1100' s communication program, contains all the features, WOR, CCA, RX TX, etc.
ModbusMaster
- ModbusMaster.h - Arduino library for communicating with Modbus slaves over RS232/485 (via RTU protocol). This file is part of ModbusMaster. ModbusMaster is free software: you can redistribute it and/or modify it under the terms o
RF2411_avr(RF2401EK)
- 用NRF2401实现无线收发，与51单片机连接的时候，需要加电阻。-The nRF2401A can be programmed using a simple 3-wire interface where the data rate is decided by the speed of the micro controller. By allowing the digital part of the application to run at low speed while maximi