搜索资源列表
dvbmpeg2analyser
- 这是本人参与实验室项目编写的实现dvb-mpeg2码流解复用中和码流相关的源代码，用c实现，dsp是ti的5416，中间用到了，计时、中断、时钟锁存寄存器设置，对于学习dsp编程很有帮助-This is my participation in the project prepared by the laboratory to achieve DVB-mpeg2 stream demultiplexing and in bitstream relevant source code, using c
Lab05-Timer
- TMS320C6713 DSP 定时器源码，实现定时-TMS320C6713 DSP timer source to achieve timing
DTK-TIMER1111
- DSP定时器程序，SEED公司的完整的DSP定时-DSP timer procedures SEED integrity of the company's DSP Timing
f2812ds1302
- ds1302,时间芯片，在dsp开发环境下的源代码，tmsf2812,运行正常-ds1302, timing chips, dsp development environment in the source code, tmsf2812. Operation
cpd_tidsp
- CP detector (CPD) only reports the onset and removal of a tone. The analysis of timing (if required) shall be responsibility of a higher-level application due to uncontrollable variability of those parameters from country to country.FOR TI C54X/C
zhongduanqi
- DSP开发系统实验——中断器实验，利用定时器的定时能够准确设定定时时间-DSP Development System Experiment- Experimental interruption of the use of timer settings from time to time to accurately timing time
I2C_DSP
- 在DSP上实现I2C的时序，通过编译，可以直接调用读写E2PROM，欢迎大家下载-In the DSP to achieve I2C timing, by the compiler, you can direct calls to read and write E2PROM, welcome you to download
CTune0.9
- 主要用于时序分析,无论是ASIC还是FPGA以及DSP都很有效的.欢迎大家使用-Mainly used for timing analysis, whether it is ASIC or FPGA and DSP are very effective. Welcome to use
delay
- 通过程序实现N个时钟的延时，并实现定时的功能-N through the implementation process of the delay clock, and realize the function of timing
Timer_test
- DSP LF2407的定时器用例，采用中断方式精确计时-DSP LF2407 timer with cases, the use of precision timing interrupt
fft
- 由TI-28xx範例程式，更改TI到可以Complete，把缺的資料放入和更改記憶體時序-TI-28xx example from the program, changes in TI to a Complete, the lack of information on Add and change the memory timing
2407ADC
- 该程序用事件管理器B的定时器4定时时间来触发A/D采样的启动。采样时采用级联模式，一次做16个转换，转换通道分别是0~15。转换完成后，在A/D中断服务子程序中将转换结果读出。该程序做一次A/D采样。 -The program manager with the events of the timer 4 timing B to trigger A/D sampling start. Sample used in cascade mode, do a 16 conversion, conver
DSP2812_LM3037
- DSP2812控制的LM3037程序，采用串行通信模式，时序比较复杂，请读者参照DATASHEET。-DSP2812 the LM3037 control procedures, the use of serial communication mode, timing is rather complicated, please refer to the reader DATASHEET.
comparetodiscontiune
- 本程序通过对DSP2407A的定时器进行定时操作-Through this program the timer for timing operation DSP2407A
TImer
- 能较为准确的计时并将时钟、分钟、秒钟显示到数码管上，此实验是利用DSP的定时器做时钟，并将时钟、分钟、秒钟显示到数码管上。编写程序时先编写定时器初始化程序，运用DSP定时器来定时计数，并通过定时器中断服务程序刷新数码管。其硬件连接原理图和I/O端口地址译码请参考实验五输入输出模块中的数码显示输出模块。-Can be more accurate timing and the clock, minutes, seconds display to digital control, this exper
source1
- 用dsp控制led灯 并定时一秒钟实现灯的点亮和熄灭，-Dsp control the timing lights with light and extinguish
dsp2812_source_code
- dsp2812的各类借口和外设源程序包括ADC,CAN口，SCI通信，SPI通信，TIMER定时，写FLASH等等，十分实用。-dsp2812 source of all kinds of excuses and peripherals including ADC, CAN port, SCI Communications, SPI communication, TIMER timing, write FLASH, etc., which are very useful.
ceva_timer
- 这是一个利用DSP上的TIMER计时的程序，应用时只要在工程中把这两个文件加上即可。-This is a TIMER on the use of DSP timing of the program, application as long as the project can add these two files.
GPIO_LCM
- 该文件是GPIO模拟时序，实现SPI协议的代码。-This file is GPIO analog timing to achieve SPI protocol code.
Timing-control-display-of-lights
- 指示灯定时控制显示。这是在CCS环境下运行的，是DSP的一个实验-LED timing control display. It is run under the CCS is an experimental DSP