资源列表
STC12C5A60S2模块程序
- 最新配套1T（STC12C5A60S2单片机)实验21个，注意LCD12864 步进电机需要用手机5V供电器供电，否则可能影响实验效果，因电脑USB口电流比较小，详细实验方法请看每个实验里的说明，看明后再做实验。(Form a complete set of the latest 1 t 21 (STC12C5A60S2 SCM) experiment, note LCD12864 stepper motor need to use their phones to 5 v for the ele
TFTLCD
- 2.4/2.8寸TFT液晶驱动 支持驱动IC型号包括:ILI9341/ILI9325/RM68021/ILI9320/ILI9328/LGDP4531/LGDP4535/SPFD5408/SSD1289/1505/B505/C505等(2.4/2.8 TFT LCD driver)
dianzicheng
- 电子秤proteus仿真和程序资料，c语言(Electronic scales proteus simulation and program information, C language)
1
- 简易的年月日 日历设计，proteus仿真文件(proteus Simple calendar design, proteus simulation file)
STC15-4jdq
- 基于STC15开发的蓝牙模块控制4路继电器模块源程序及原理图(STC15 based Bluetooth module control 4 relay module source code and schematic diagram)
1.工程的建立
- STM32F407ZG在MDK5上的工程模板，有库函数，寄存器两个版本(STM32F407ZG project templates on MDK5,there are library functions, registers two versions)
closed-loop control .X
- 程序包含闭环控制技术以及实时检测功能，可以将传感器的信号作为反馈量，实时调节控制的状态，达到最优控制的目的。(Program includes closed-loop control technology and real-time detection function.Adjust the state of the control in real time to achieve the purpose of optimal control.)
UART.X
- 利用串口与上位机通信，实时采集电信号并显示，最后以通信的方式返还给上位机。(Using serial port to communicate with the host computer, real-time acquisition of electrical signals and display, and finally return to the host computer by means of communication.)
communication.X
- 利用SPI接口进行CAN总线通信，单片机可以通用，只需要有SPI模块即可转换成CAN总线形式。(Using SPI interface for CAN bus communication, single-chip microcomputer can be universal, only need to have SPI module can be converted to CAN bus form.)
ADC
- 将4路模拟量4-20mA电流信号通过I\V变换将信号送至AD模块， 实现数模转换，送入单片机，经单片机处理后，再次通过DA转换和V\I变换， 输出，最后连接一个远程通讯模块连接至上位机。(The 4 analog 4-20mA current signal is transmitted to the AD module via the I\V transform, Realize digital to analog conversion, into the microcontroller,
AD-DMA
- 通过DMA把ADC结果存入DMA的RAM中，使用时可以在程序内部直接读取，比EEPROM方便快捷。包含PROTEUS仿真电路图。(Through DMA, the ADC results are stored in the DMA of RAM, and it can be read directly inside the program when using. It is more convenient and faster than EEPROM.)
高通芯片字库导出检验工程-stm32f4平台
- 通过SPI总线方式，调用字库芯片，再通过RS485显示到上位机上的结果来测试调用功能(Through the SPI bus mode, call the font chip, and then through the RS485 display to the host computer results to test the call function)