资源列表
uart
- PIC单片机PIC16F877A 串口数据收发程序，已经经过测试可以使用。-PIC16F877A PIC microcontroller serial data transceiver procedures have been tested can be used.
motor
- 单片机PIC16F877A控制步进电机程序， 根据四相步进电动机的工作原理，通过控制输出脉冲信号的分配组合、顺序、次数、和频率实现对电动机的工作方式，旋转方向，位置和速度等控制要素进行控制。-Microcontroller PIC16F877A stepper motor control procedures, according to the four-phase stepper motor works by controlling the distribution of the combin
hongwai
- 单片机PIC16F877A红外收发实验。使用串口发送数据经调制后从红外管输出，并通过红外接收模块把接收到的数据返回串口接收端，通过判断接收到的数据来控制LED灯点亮。-PIC16F877A microcontroller infrared transceiver experiments. After using the serial port to send data modulated output the infrared tube, and through infrared receiv
less_inductance
- 采用单片机PIC16F877A 编写的基于串联谐振主回路的感应加热程序，实现对谐振频率的自动跟踪，已经过阻性负载和感性负载实验，实验结果良好。-Based on written using PIC16F877A microcontroller series resonant circuit induction heating main program, automatic tracking of the resonance frequency has been resistive load an
DS18B20
- ds18b20 is measuament T
DigitalFilter
- 音乐（语音）通过语音芯片转化为差分输出的模拟量电压信号，经过差分减法电路转化为单端信号，AD转换芯片将模拟信号转化为数字信号。利用单片机设计数字滤波器对语音信号进行处理，根据低通、带通和高通三个滤波器的计算结果输出三路PWM信号。三路PWM信号经驱动电路分别控制LED光带红、绿和蓝三种颜色的亮度，灯光颜色明暗随音乐变化。-Music (Voice) by voice chip into a differential output analog voltage signal, through a
STC
- STC全系列单片机的C语言头文件，大家用C开发STC单片机时，会用的上-STC full range of microcontroller C language header files STC microcontroller development with C on
OSC_Cry1
- 此例程说明如何配置外部振荡器驱动22.1184Mhz晶体及如何选择此外部振荡器作为系统时钟 同时使能丢失时钟检测器复位功能。 假定22.1184Mhz晶体连接在XTAL1和XTAL2之间-This routine shows how to configure an external crystal oscillator drive 22.1184Mhz and how to this external oscillator as the system clock while Enable
ADC0_Poll1
- 此例程说明了 ADC0在查询模式的操作 ADC0设置为写AD0BUSY作为其转换开始信号 并测量片内温度传感器的输出温度传感器的输出转换成摄氏度并从UART0传输。-This routine illustrates the ADC0 ADC0 set the query mode in operation for write AD0BUSY as its conversion start signal and measuring the on-chip temperature sensor
ADC0_Buf1
- 此程序为使用ADC0的例程 在中断模式使用定时器3溢出作为开始启动信号并采样AIN0<NUM_SAMPLES>次将结果存储在XDATA空间 一旦<NUM_SAMPLES>次被采集 采样值从UART0传输 一旦传输结束 另一个数据采样次数<NUM_SAMPLES>将被采集并重复此处理过程.-This procedure for routine use ADC0 interrupt mode using the timer 3 overflow started a
SIN_SPWM
- 利用SPWM调制产生正弦信号，可运用与各种电子器件的测量，如电压、电容、电阻等。-SPWM modulation using sinusoidal signal can be measured with the use of various electronic devices, such as voltage, capacitance, resistance and the like.
033T-CP
- ATT功能,PE4302串口控制，初始值为无衰减,RU监控板CDMA DL编码开关手动设置、OMT对应远端机CDMA DL ATT均可设置，与手动的衰減器设定值，以最后的操作方式为主，设定值在系统重启后仍然保持最后的设定值；-ATT function, PE4302 serial control, the initial value without attenuation, RU monitoring board CDMA DL coding switch manually set, OMT c