搜索资源列表
gray_data
- 本程序可自动产生数据，存入存储器中并转化为格雷码，按时序输出。-This program can be automatically generates data such as the memory of deposit and translated into gray code, and the output time sequence.
93C46-8051
- IIC的接口时序模拟程序，使用8051的普通GPIO口进行模拟，实现发送数据、接受数据。程序已经经过验证！-The IIC interface timing simulation program that uses ordinary GPIO port 8051, simulation, and send and receive data
EXCEL-TIMING
- 自制的EXCEL画时序图程序 输入10101010二进制数值即可显示 输入数据前需加“ ”单引号，不然会被自动转换成科学计数 -Homemade the EXCEL draw timing diagram program input 10101010 binary values to display the input data need to add the " ' single quotes, otherwise it will be a
FPGA0
- SRAM读写时序，先读入一串数据，然后再实现输出-SRAM write and read
chuankoutiaoshi
- 串口RS232的通信时序和逻辑设计，实现数据FGPA与PC之间数据的相互传输-RS232 serial port communications timing and logic design, the mutual transfer of data between FGPA and PC data
I^2C
- 利用单片机普通IO口模拟I2C时序，实现串行通信。并将数据写进E2PROM，实现数据掉电保存-Microprocessor IO port simulation I2C timing, serial communication. And the data is written into the E2PROM, data power-down save
RF905data
- nrf905无线通信模块，spi时序，实现快速收发，数据接收处理。-nrf905 wireless communication module spi timing, and quickly send and receive data receiving and processing.
MzT43V10_MCS51_8bitGPIO
- MzTH56模块串行SPI接口，最高支持时钟频率为18MHz，指令以及数据的写入时序相同-MzTH56 module serial SPI interface, the maximum support clock frequency of 18MHz, the instruction and data write timing
music_player
- 用Verilog语言在FPGA上实现了音乐播放这一功能。预先将音乐《北京欢迎你》转换保存到FPGA的ROM中，由设计的音乐播放器按时序读出数据，予以播放。-Using Verilog language in FPGA realize the function of playing music.The music of "welcome to Beijing" was transformed and saved in FPGA ROM, the data was read by music pl
EEPROM
- 该驱动程序库包含了I2C总线基本时序以及AT24C系列EEPROM的读写函数.还包含了常用数据格式变量的保存、读取函数。除了字节读写之外，还可以很方便的向EEPROM里写入和读出整型、浮点数、长整型格式的数据。-The driver library includes the basic timing of the I2C bus and EEPROM read and write functions AT24C series. Also includes a common data format
CH452
- 程序功能为51单片机通过三线串口操作CH452，CH452驱动8位数码管正常显示以及显示数据的更新。51单片机通过模拟CH452串口操作时序向-The program features 51 microcontroller via a three-wire serial interface operation CH452, CH452 driver 8 digital tube display properly, and display data update. 51 single-chip C
cpld_ads7844_50M(9-24)
- 用ads7844采集数据，用cpld做时序控制，通过串口观察和记录采集结果，用verilog编写，通过开发板验证-Collected data using ads7844 timing control with cpld verilog prepared by the serial observe and record collection results through the development board verification
lcd12864
- 详细介绍的LCD12864的分类，数据操作，访问等具体指令，时序以及12864的多种操作方法。-LCD12864 the detailed classification of data manipulation and access specific instructions, timing and 12864 multiple operating method.
vhdl_text2
- 设计输入数据宽度是4bit的ADD、SUB、MULT、DIVIDE、COMPARE 把它们作为一个project,DEVICE选用EPF10K70RC240-4，对它们进行 时序仿真，将仿真波形-Design input data width the 4bit ADD, SUB, MULT, DIVIDE, COMPARE them as a project, the DEVICE selection EPF10K70RC240-4, and timing simulation, s
vhdl_text3
- 设计一个数据宽度8bit，深度是16的 同步FIFO(读写用同一时钟)，具有EMPTY、FULL输出标志。 要求FIFO的读写时钟频率为20MHz， 将1－16连续写入FIFO，写满后再将其读出来（读空为止）。 仿真上述逻辑的时序-Design a data width 8bit depth of 16 the synchronization FIFO (read and write with the same clock), EMPTY, FULL output fla
OV7670照相模组硬件应用指南
- OmniVision公司机密 1. OV7670 模组参考设计 注： 1.PWDN和RESET不用时，应接地 2. OV7670 模组接口参考设计 2.1 引脚定义 2.2 电源供给 3. OV7670 照相模组操作 3.1 节电模式 3.2 照相模组工作在不断电的节电模式 3.2.1 上电，硬件复位 3.2.2 上电，软件复位 3.2.3 由不断电的节电模式恢复工作 3.2.4 不断电的节电模式 3.3 照相模组工作在断电的节电模式 3.3.1 上电 3.3.2
NV020SD
- NV020SD语音播报模块，资料齐全：C语言程序，电路图，时序图，数据手册等，推荐！-NV020SD voice broadcast module, complete information: C language program, circuit diagrams, timing diagrams, data sheet, it is recommended!
Dht11
- 采用单总线方式与cpu进行数据传输，与DS18B20相似，对时序的要求比较高，不同之处在于写程序的时候数据的采集必须间隔1s以上，不然采集会失败。此篇将利用arduino驱动DHT11，检测环境温湿度情况。-The cpu data transfer using a single bus with DS18B20 similar timing requirements are relatively high, the difference lies in the writing program
DS18B20
- 本源码用verilog实现对DS18b20温度传感器的时序控制，使DS18b20能正常工作，获得温度数据-The source verilog of DS18b20 temperature sensor timing control, so DS18b20 can work to obtain temperature data
SD
- 主要用与单片机对SD卡的操作，数据的读写时序的操作-The main and the SCM SD card operation, data read and write sequential operation