搜索资源列表
高级图形学期末大作业
- 实现机器人带光照的绘制和运动变换。通过glPushMatrix() 和glPopMatrix()绘制出机器人层次结构模型和几何变换，要求实现机器人手、脚、头、肩膀的旋转等几何变换，能够实现机器人走路的效果。同时机器人应打上光照。(It realizes the robot's rendering and motion transformation with illumination. By glPushMatrix () and glPopMatrix (), the robot hierarc
_低照度视频图像增强算法综述.pdf
- 低照度视频图像增强，这是一个论文，描述了一些常用的低照度视频图像算法(Low illumination video image enhancement, which is a thesis, describes some commonly used low illumination video image algorithms.)
Gamma
- 利用多尺度高斯函数去除场景的光照分量；然后构造了一种二维伽马函数，利用光照分量的分布特性调整二维伽马函数的参数，降低光照过强区域的亮度值，提高光照过暗区域的亮度值，最终实现对光照不均匀图像的自适应校正处理。(The multi scale Gauss function is used to remove the illumination component of the scene, and then a two-dimensional gamma function is constructed
光强检测
- 基于单片机，检测光照强度，并通过0.96寸oled显示出来。(Based on single chip microcomputer, the intensity of illumination is detected and displayed through 0.96 inch OLED.)
mpiv_toolbox
- 用matlab生成特定的数字散斑图像,比方说生成一个101*101的散斑图像，里面含有200个散斑之类的(In describing the first-order properties of laser speckle under polarized illumination conditions, it is almost an article of faith that the contrast is unity. In many processing schemes, however,
WhiteBalance_10bit
- 模块功能：通过白平衡消除由光照带来色差（绿雾） 模块输入：亮度增益输出R,G,B三通道像素值（double） 模块输出：白平衡后R,G,B三通道像素值（double）(Module function: to eliminate chromatic aberration (green fog) caused by illumination through white balance. Module input: brightness gain output R, G, B three c
关闭树莓派指示灯
- 晚上开着的树莓派老亮着那盏红色电源指示灯，感觉非常不舒服，狠想关掉它！我还是比较喜欢把麒麟座上的RGB灯调成蓝色做小夜灯，毕竟往上照射的灯光不会让人感觉不舒服。 将以下几行加到 /boot/config.txt 即可禁用树莓派 Model 2B 的两盏指示灯。(The raspberry pie that was on at night was always lighting the red power indicator. It was so uncomfortable that it wa
BH1750程序
- 通过使用STM32F407，和1750光照传感器，实现对光照度数据的采集(The illumination data acquisition is realized by using STM32F407 and 1750 light sensors.)
VCSEL-DOE_design with distortion
- Design grating and simulate its diffracted orders with distortion. It can be used to design the dots-pattern illumination for structured-light 3D detection. 用于光栅设计和仿真其衍射级次的畸变效果。该程序能够用于设计点阵形式的结构光照明，以进行3D结构光测量。
光敏传感器数码管1.1(C8T6)
- 本设计依靠光敏电阻对光照敏感的特点，自动检测并显示当前所在环境的光照强度，并根据光照强度的大小，来控制继电器，从而控制路灯的开启和关闭。 该设计可分为四部分:即光照检测部分、信号处理部分、显示部分和执行部分。 光照检测部分利用光敏电阻的特性（光照越强阻值越小，光照越弱阻值越大），通过检测光敏电阻两端电压变化的模拟量，来反映光照强度。(This design relies on the photoresistor's sensitivity to light, automatically de
特征匹配
- MATLAB实现图像的SIFT特征提取，并做在不同光照、不同视角下的特征匹配(MATLAB realizes SIFT feature extraction of image and matches features under different illumination and different visual angles)
PV_MPPT
- 通过电导增量法实现光伏MPPT控制，改变光照强度可以看出最大功率输出改变。(The photovoltaic MPPT control is realized by the conductance increment method, and the maximum power output change can be seen by changing the illumination intensity.)
17281022-王誉杰-第二次作业
- Opengl光照鼠标键盘控制位移贴图等等，附带视频展示说明等等大量信息(Opengl illumination, mouse keyboard control, displacement mapping, etc., with video presentation instructions)
Gamma-correction
- 对图像进行伽马校正，可以有效提升图像 亮度和对比度，低于低照度图像现在小于1的参数，对于高亮度的图像选择大于1的参数可以有效调节图像亮度。(Gamma correction can effectively improve the brightness and contrast of the image. The parameters lower than the low illumination image are less than 1. For the high brightness ima
PV
- 基于simulink的光伏电池建模，输出为光照、温度条件变化之后的P-U和I-U曲线。(Based on the Simulink photovoltaic cell model, the output is P-U and I-U curves after the change of illumination and temperature conditions.)
22.1、MAX44009+BME280(USART)
- 采用STM32实现MAX44009光照传感器的照度采集，串口通信(Using STM32 to realize illumination collection and serial communication of max44009 light sensor)
twodgamma
- matlab 基于二维伽马函数的光照不均匀图像自适应校正算法(Adaptive correction algorithm of illumination nonuniformity image based on two-dimensional gamma function)
单片机的校园智能照明控制系统的设计
- 通过上传室内信息，有人无人，光照度，天气，来调节灯光的开关，通过上位机可以设置自动和手动模式(By uploading indoor information, there are no people, illumination, weather, to adjust the light switch, through the upper computer can set automatic and manual mode)