资源列表
autoseller
- 设计FPGA模块模拟自动售货机的工作过程，功能如下（1）售货机有两个进币孔，一个是输入硬币，一个是输入纸币，硬币的识别范围是5角和1 元的硬币，纸币的识别范围是1 元、5 元，10 元，20 元，50元，100元。乘客可以连续多次投入钱币。（2）顾客可以选择的商品种类有16种，价格分别为1-16元，顾客可以通过输入商品的编号来实现商品的选择。即有一个小键盘（0-9按键）来完成，比如输入15时要先输入1，再输入5。（3）顾客选择完商品后，可以选择需要的数量。然后可以继续选择商品及其数量，每次可以选
FPGAPVC
- 基于PCI的LED跑马灯,上位机点亮LED跑马灯，桥芯片为PLX9054-PCI-based LED Marquee, PC lit LED marquees, PLX9054 bridge chip
FPGAPVC_2
- 基于PCI的数据发送源,上位机为VC编写，桥芯片为PLX9054，项目已经做完，上传5个例程，已经验证通过-PCI-based data transmission source, PC for VC preparation, bridge chip for PLX9054, the project has been done, upload 5 routines, has been verified by
FPGAPVC_3
- 基于SDRAM的PCI采集,上位机为VC编写，桥芯片为PLX9054，项目已经做完，上传5个例程，已经验证通过-SDRAM, PCI-based acquisition, PC for VC preparation, bridge chip for PLX9054, the project has been done, upload 5 routines, has been verified by
FPGA_4
- 无PCI控制的LED跑马灯,这个例程相对简单一些，主要用来验证FPGA是否正常工作-No PCI controlled LED marquees, this routine is relatively simple, mainly used to verify that the FPGA to work
FPGA_5
- 无SDRAM的PCI采集,给出PCI采集的FPGA程序，桥芯片也为PLX9054，已验证通过-No SDRAM, PCI capture, given FPGA PCI acquisition program, bridge chips for PLX9054, has been verified by
ALL_6
- 这是项目总的文件夹，包括原理图，PCB,上位机VC程序，驱动程序，下位机FPGA程序，可做为开发板，LVDS采集开发板，前面上传的5个位五个测试程序，已经验证其正确性，需要的可以参考。-This is the total project folder files, including schematics, PCB, PC VC, the driver, the next crew FPGA program can be used as the development board, LVDS c
MUSIC_PLAYER
- 可以播放四首乐曲，设置play、next、reset三个按键。按play键播放当前乐曲，按键next播放下一首乐曲。 LED0指示播放情况（播放时点亮）、LED2和LED3指示当前乐曲序号。-You can play four songs, set play, next, reset three keys. Press the play button to play the current song, button next to play the next song. LED0 ind
UPPER-BODY-MOTION-TRACKING
- 基于fpga的人体上半肢体动作检测，vga显示。-realtime upper body motion tracking based on FPGA
led1
- 基于FPGA编程的流水灯，很适合初学者入门的初学者学习与使用，欢迎大家下载-The scope of this document is, to define the content of the physical layer and the basic characteristics of the physical medium, for communication according to the Controller Area Network protocol specificati
The-decoder
- 基于FPGA的38译码器程序，非常适合初级菜鸟学习使用入门程序，欢迎大家下载学习-Program 38 decoder based on the FPGA, very suitable for learning to use primary rookie entry procedures, are welcome to download the learning
thecode
- 基于FPGA的多路选择器程序，非常适合初级菜鸟学习使用入门程序，欢迎大家下载学习-FPGA multiplexer based procedures, very suitable for learning to use primary rookie entry procedures, are welcome to download the learning